Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Branch Circuits

User: Echoengineer, Location: Santa rosa

Asked on: Wednesday, September 25, 2024 at 3:46 pm EDT
Answered on: Thursday, March 6, 2025 at 2:56 am EST

Question: I've recently ran into an issue on a project that I'm working when sizing a panelboard that can accommodate the customers needs. Here is the situation. I have a 300kva pad mount transformer that provides 480Vac to a 400A service disconnect. From this disconnect I have sized a panel from Eaton, PRL3X that has a 600A bus with a 400A ECB main. The specs of this panel indicate an max branch circuit rating of only 225A. Customer has a 200HP pump that requires at minimum a 300A OCPD. Would it be allowable to use a 300A branch circuit when the panel is rated to support a max of 225A?

Okay, let's break down this panelboard situation and address the 300A breaker requirement for the 200HP pump. You're right to be cautious – exceeding the panel's listed limitations is a significant safety and code compliance concern.

The Problem



Panelboard Busbar Rating

You have a panelboard with a 600A busbar. This means the busbars
themselves can handle 600A continuously.

Main Breaker

You have a 400A main breaker. This protects the entire panel from drawing more than 400A.

Maximum Branch Circuit Rating (Critical Issue)

The PRL3X panel specifies a
maximum branch circuit breaker rating of 225A. This is the limiting factor here.

Pump OCPD Requirement

The 200HP pump requires a 300A overcurrent protective device (OCPD) – you need to account for inrush and motor starting characteristics.

Why You Can't Just Use a 300A Breaker in a 225A Max Panel


Listing and Labeling Violations

The panelboard is listed and labeled with a maximum branch circuit breaker rating. Exceeding this violates the panel's UL listing (or other relevant standards) and likely violates the National Electrical Code (NEC) Article 110.3(B) - "Installation and Use of Equipment." This section requires equipment to be installed and used according to its listing and labeling instructions.
2.


Overheating and Failure

The internal components (stabs, connections, etc.) in the panelboard associated with the branch circuit positions are designed and tested only up to the rated maximum breaker size. Using a larger breaker can cause these components to overheat, potentially leading to insulation breakdown, arcing faults, and fire.3.

Increased Arc Flash Hazard

A larger breaker than the panel is rated for can compromise the panel's arc flash withstand rating and protective schemes.

Possible Solutions and Considerations

Here's what you need to do to properly address this situation:1.

Verify Pump OCPD Sizing

Double-check your calculations for the 300A OCPD. Is this based on NEC Article 430 (Motors, Motor Circuits, and Controllers)? Make sure you're using the correct Full Load Amps (FLA) from NEC Table 430.250 and applying the appropriate multipliers for starting current and type of motor. It's possible, though unlikely for a 200HP motor, that you've overestimated the required OCPD size. Note: The 300A is most likely correct2.

Use a Feeder Breaker (If Acceptable)

Instead of landing the 300A breaker directly in the panel, you could feed a separate disconnect or fusible disconnect with the 300A protection from the panel. This disconnect would then feed the pump controller. You would need to install a 225A breaker in the panel to feed this disconnect.3.

Consider a Motor Starter with Overload Protection

For a 200HP motor, a motor starter with properly sized overload relays is essential for motor protection. You can use a properly sized breaker (e.g., 225A) in the panel to feed the motor starter. The overload relays in the starter will protect the motor from overloads, and the breaker will provide short-circuit and ground-fault protection for the entire motor circuit. This can be a common approach for large motors. Verify if this meets all code requirements.4.

Change Panelboards

The most straightforward (but potentially most expensive) solution is to replace the existing panelboard with one that is listed and rated for the required 300A branch circuit breaker. You'll need to find a panel with a 600A (or higher) busbar rating AND a branch circuit breaker rating of at least 300A. Check catalogs from Eaton, Square D, Siemens, and other major manufacturers. The Eaton PRL2A series, or similar offerings from other manufacturers, will often accommodate larger breakers.5.

Separate Disconnect/Panel for the Pump

Consider a separate disconnect or a small sub-panel specifically for the pump. This would be fed from the 400A service disconnect with appropriately sized conductors and a suitable breaker.6.

Consult with Eaton (Panelboard Manufacturer)

It's always wise to contact Eaton's technical support. They may have specific solutions or clarifications regarding the panel's limitations or potential workarounds (although it's highly unlikely they will endorse exceeding the listed breaker rating).

Crucial Considerations



NEC Compliance

Ensure any solution you implement is fully compliant with the latest edition of the National Electrical Code (NEC).


Local Codes and AHJ

Be sure to adhere to any local amendments to the NEC or any specific requirements imposed by your local Authority Having Jurisdiction (AHJ) – the electrical inspector.*

Engineering Review

It's strongly recommended to have a qualified electrical engineer review the entire design and calculations to ensure compliance and safety.

In summary, you cannot install a 300A breaker in a panelboard that has a maximum branch circuit breaker rating of 225A. It violates the panel's listing and could create a dangerous situation. You must find a solution that either uses a different panel, feeds the motor starter with overload protection, or utilize an approved method to meet the requirements.
Flag for review

Previous Question Next Question