Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Egress from a Substation

User: Safety Rep Jeff, Location: Hagerstown MD

Asked on: Thursday, September 26, 2024 at 10:55 am EDT
Answered on: Thursday, March 6, 2025 at 2:59 am EST

Question: I have an interior substation that has 1200 amps or more and is over 6 feet wide. There are 2 emergency egress doors located in the room. One of the doors leads to an open area in the facility. The other door opens into another room containing other equipment. One of these being an air compressor. One door egresses north and the other egresses south (this is the one that goes into another room). My concern is if you are working on the west side of the equipment and there is an emergency (i.e. an arc flash), there is no way to reach either of these doors. I have been arguing with the facility director that there needs to be an egress on the west side of the area. This would alleviate the need to try to reach the doors on the other side of the equipment. There was a door on the west side, but this was replaced by a manual roll up door. Any suggestions?

You're right to be concerned. You've identified a serious potential safety hazard. Here's a breakdown of your situation and some suggestions for approaching it

Understanding the Hazards
Arc Flash Hazard

Substations with equipment rated for 1200 amps or more are significant arc flash hazards. The potential for injury is high.


Limited Egress

The scenario you describe – being trapped on the west side of the equipment during an arc flash event – is extremely dangerous. The path to safety should be direct and unobstructed. Seconds matter in such a situation.

Roll-Up Door

A manual roll-up door is
not an adequate egress solution in an emergency. It's too slow and potentially cumbersome to operate under duress or with impaired vision.

Room with Other Equipment

Exiting into a room with an air compressor presents a secondary hazard. Compressed air systems can have their own safety risks, especially in a panic situation.

Relevant Codes and Standards (Important for supporting your argument)
NFPA 70E (Standard for Electrical Safety in the Workplace)

This is the primary standard addressing electrical safety and arc flash protection. It emphasizes hazard assessments, safe work practices, and emergency preparedness, including clear means of egress.


NEC (National Electrical Code, NFPA 70)

While primarily focused on electrical installation, the NEC addresses egress and working space around electrical equipment. Look for articles related to working space around electrical equipment (110.26) and means of egress.

OSHA (Occupational Safety and Health Administration)

OSHA adopts many NFPA standards. If OSHA inspects your facility, they will likely cite violations related to inadequate egress and arc flash hazards based on NFPA 70E.


IBC (International Building Code)

This code may govern the overall building design, including egress requirements from high-hazard areas. Local building codes may supersede the IBC.

Your Argument to the Facility Director


Here's a structured approach to convince your facility director:1. Document the Hazard (Written Report)

Create a formal, written report outlining the following:

Specific Description

Clearly describe the layout of the substation, including dimensions, equipment locations, door locations, and the presence of the roll-up door. Include a diagram if possible.


Hazard Identification

State explicitly the arc flash hazard and the risk of being trapped on the west side of the equipment. Explain how the roll-up door is inadequate for emergency egress.

Risk Assessment

Conduct a formal risk assessment (following NFPA 70E guidelines) that quantifies the likelihood of an arc flash event and the potential severity of injuries given the current egress limitations. This might require the assistance of a qualified electrical engineer or safety professional.


Code/Standard Violations

Cite specific sections of NFPA 70E, NEC, OSHA regulations, or local building codes that are being violated by the inadequate egress.

Recommendations

Clearly recommend the re-establishment of a functional egress door on the west side of the substation. Suggest alternative solutions, such as:


Re-installing a swing-type door

This is the most direct and likely the best solution.

Installing a powered (automatic) roll-up door

If a swing door is impossible, a
powered roll-up door that opens immediately upon activation of an emergency button or fire alarm system might be considered, but it needs to be carefully evaluated for reliability and speed of operation. It still has drawbacks compared to a swinging door.

Relocating Equipment

While less likely, could equipment be rearranged to provide a clearer path to an existing egress?

Photos/Visuals

Include photos of the area, highlighting the equipment, door locations, the roll-up door, and the lack of a clear egress path.2.

Present the Report Formally

Schedule a meeting with the facility director to present your report in person.3.

Focus on Safety and Liability

Emphasize the potential for serious injury or death and the company's potential liability if an incident occurs.4.

Quantify the Risk (if possible)

If you can get data on the frequency of arc flash events in similar installations, use that to highlight the probability of an incident.5.

Offer Solutions, Not Just Problems

Present your recommendations as cost-effective solutions to mitigate the identified risks.6.

Escalate If Necessary

If the facility director is unresponsive, escalate the issue to higher management or the company's safety officer. Document all communication and actions taken.7.

Involve Qualified Professionals

If necessary, bring in a qualified electrical engineer or safety consultant to conduct a professional hazard assessment and provide expert recommendations. Their opinion will carry more weight.

Additional Considerations
Signage

Ensure that egress doors are clearly marked with illuminated "EXIT" signs.

Emergency Lighting

The substation should have adequate emergency lighting that activates in the event of a power outage.


Employee Training

All employees who work in or near the substation should be trained on arc flash hazards, emergency procedures, and egress routes. Practice drills can be very helpful.

Arc Flash Study

Has a full arc flash study been conducted on the substation? This is crucial for determining the potential incident energy levels and for selecting appropriate PPE (Personal Protective Equipment).


Coordination Study

Have protective devices been properly coordinated? Improper coordination can increase arc flash hazard levels.

Don't Give Up:
Your persistence is crucial. Your concern for safety is valid, and you have a responsibility to advocate for a safe working environment. Document everything, follow the chain of command, and involve qualified professionals when needed. The safety of yourself and your colleagues depends on it. Flag for review

Previous Question Next Question