User: nizak, Location: New Jersey
Asked on: Thursday, September 26, 2024 at 9:02 pm EDT
Answered on: Thursday, March 6, 2025 at 3:02 am EST
Question: I’m posting this here because there seems to be much more attention paid to this heading.I’m looking to figure exterior lighting for a restaurant that recently installed a canopy with business name along the entire width of the front of their building.Planning to use damp rated LED strips. The top of the canopy is completely enclosed . Would it be safe to say it’s a damp and not a wet location?My thought is to run the fixtures horizontally across the entire width half way up the height . That height would be where the lettering is located.Should the fixtures be continuous ( end to end) or have some spacing between them.Would dark spots be evident with say a 12” spacing between fixtures?Thanks
You're right, this section should get more visibility. Let's break down your restaurant canopy lighting project
1. Damp vs. Wet Location:
Your Scenario
With the top of the canopy being completely enclosed, it's highly likely you're dealing with a
damp location. A wet location would be directly exposed to rain, splashing, or saturation. The enclosed canopy protects the LED strips from direct precipitation, even though humidity and condensation can still be present. Verification
To be absolutely sure, check your local electrical codes. They often define "damp" and "wet" locations precisely. You might also consider the local climate. If you're in an area with frequent heavy rain or snow, there might be a greater chance of water ingress even under a canopy.
2. LED Strip Placement and Spacing
Horizontal Run at Lettering Height
Positioning the lights halfway up the lettering height is generally a good strategy. This should provide even illumination of the signage.
Continuous vs. Spaced
This is a key design question, and the answer depends on several factors:
Desired Aesthetic
A continuous run provides a more uniform, "glowing" effect, while spaced fixtures can create a more distinct, dotted, or segmented appearance.
LED Strip Brightness (Lumens per foot)
Higher brightness strips can tolerate more spacing. Lower brightness strips might require closer spacing or a continuous run.
Beam Angle
The LED strip's beam angle (how wide the light spreads) is critical. Wider beam angles will blend the light better and reduce dark spots with spacing. Look for strips with a wide beam angle (120 degrees or more).
Lettering Material
Opaque lettering will show dark spots more readily than translucent lettering.
Budget
Continuous runs will obviously cost more due to the increased material and installation time.
Dark Spot Potential with 12" Spacing
Yes, 12" spacing could create noticeable dark spots, especially if: The LED strips have a narrow beam angle. The LED strips are not very bright. The lettering is opaque. The installation height is low, thus each fixture can't cover enough area.To mitigate this, consider a test run. Buy a short length of the LED strip you're considering. Mount it on a board with the same spacing you're considering (12 inches), and observe the light distribution. This will be the most reliable way to assess dark spot potential.3. Recommendations and Best Practices
Prioritize Testing
The best advice is to perform a physical test with sample LED strips, mounted at the proposed height and spacing, before committing to a full installation. This allows you to visually assess the light quality and dark spot potential.
Start with Closer Spacing
If you're concerned about dark spots, start with a closer spacing (e.g., 6-8 inches) and then increase it during your test until you see unacceptable gaps in illumination.
Consider Diffused LED Strips
These strips have a coating that spreads the light more evenly, helping to eliminate hot spots and dark areas. They can be more forgiving with spacing.
Use a Light Meter (Optional)
For a more objective assessment, use a light meter to measure the illuminance (foot-candles or lux) at various points across the lettering. This will give you quantitative data to evaluate the uniformity of the lighting.
Talk to LED Strip Suppliers
Reputable LED strip suppliers can offer advice on appropriate spacing based on the specific characteristics of their products and your application. They may also have lighting design services available.
Power Supply Considerations
Plan your power supply carefully. Calculate the total wattage required for your LED strips and choose a power supply with sufficient capacity (ideally with a safety margin of 20%). Also, consider voltage drop, especially for long runs. You might need to inject power at multiple points.*
Installation
Ensure the LED strips are securely mounted and properly protected from the elements within the canopy. Use appropriate connectors and wiring for damp locations.
In summary:
A damp-rated LED strip is likely appropriate for your enclosed canopy. Spacing will depend heavily on the brightness and beam angle of the chosen LED strips. Testing is critical to avoid dark spots.By carefully considering these factors and conducting a thorough test, you can create effective and visually appealing lighting for your restaurant's canopy signage. Good luck! Flag for review