Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 2 gang box, Both 3way, outlet connected, old house

User: Kreis, Location: Ohio

Asked on: Thursday, September 26, 2024 at 10:22 pm EDT
Answered on: Thursday, March 6, 2025 at 3:02 am EST

Question: Ok , this is confusing at least to me. We just bought a house, and I got 2, 3 way switches in a single box. For some reason there is a bunch of outlets (3) connected to the light circuit in our screen room. I don't believe that's normal. I just want to know if there's a way to run a constant hot off of a 3 way switch. I apologize if this is normal and this ends up being a simple answer that I overlooked.Thank you.

Okay, let's break this down. You're not crazy, outlets on a light switch circuit are definitely unusual, though not inherently unsafe if wired correctly. And yes, it's possible to get a constant hot from a 3-way switch setup, BUT it's critical to understand how it works and why it might be a bad idea in this case.

Understanding 3-Way Switches 3-way switches don't actually switch "hot" and "neutral." They switch the "hot" wire between two different "traveler" wires. Think of it like a railroad switch. One switch sends the power down one track (traveler wire), and the other switch decides which track leads to the light. Therefore, there is no single wire that is always hot in a 3-way setup. The "hot" moves depending on the switch positions.

Why It's Probably a Bad Idea to Get a Constant Hot from Your 3-Way
Safety Concerns

Tampering with the wiring of a 3-way switch to get a constant hot can easily lead to dangerous situations:

Overloading

If you draw too much power from the "constant hot" you create, you could overload the circuit and trip the breaker (at best) or start a fire (at worst). The circuit is likely sized only for a light fixture, not multiple outlets.


Confusion

Future homeowners (or even you later) might not understand the modified wiring, leading to accidental shocks or other problems.

Code Violations

Modifying electrical wiring in a way that deviates from the National Electrical Code (NEC) can create problems when you sell the house.


Better Alternatives Exist

There are much safer and more appropriate ways to get a constant hot wire if you need one.

Safer and Better Options
1. Run a New Circuit

This is the best option. Run a new, dedicated circuit from your breaker box to the location where you need the constant hot (e.g., the outlet box in the screen room). This ensures that your new outlets have their own dedicated power supply, sized appropriately for the load. Requires running new wire and potentially installing a new breaker in your panel. Requires electrical expertise or a licensed electrician.2.

Tap into an Existing Outlet Box with a Constant Hot

Find an outlet box in the screen room (or nearby) that has a constant hot wire. You can then extend that hot wire to the location where you need it. Make sure the existing circuit has enough capacity for the additional load. Requires careful circuit tracing and knowledge of wiring techniques.

Addressing Your Original Situation: Outlets on the Light Circuit


Before you do anything, you need to figure out why those outlets are on the light switch circuit. Here's how I suggest you proceed:1. Turn off the breaker



Safety First!
Turn off the breaker that controls both the light and the outlets.2. Inspect the Wiring

Carefully remove the cover plates from all the outlets and switches involved. Take pictures of the wiring in each box before you disconnect anything. This is crucial for reassembly if needed. Look for how the outlets are connected to the light switch circuit. Are they spliced into the switch wires? Or do they run from the light fixture box?3.

Consider these Possibilities



Lazy Wiring (Most Likely)

Someone simply ran the wires from the switch to the first outlet, then daisy-chained the other outlets. The light fixture is likely the last thing on that circuit.

Controlled Outlets

Sometimes, an outlet is intentionally wired to be switch-controlled. This is usually for a lamp or appliance that you want to turn on/off with the light switch. (But you'd know if this was the case)

What to Do If You Don't Want Outlets on the Light Switch


Disconnect the Outlets from the Switch Circuit

If you can identify where the outlets are connected to the switch circuit, disconnect them.2.

Connect the Outlets to a Constant Hot Source (Safely!)

Use either of the methods described above (new circuit or tapping into an existing outlet) to provide a constant hot wire to the outlets.

Important Reminders



Consult a Professional

If you're not completely comfortable working with electrical wiring, hire a licensed electrician. It's better to be safe than sorry.

Turn Off the Power

Always turn off the breaker before working on any electrical wiring.


Use Proper Wiring Techniques

Use wire connectors to make secure connections. Properly ground all outlets and switches.

Get a Tester

Get a Non-Contact Voltage Tester, they are cheap, and will tell you if the wire is hot or not.In summary:

Don't try to derive a constant hot from your 3-way switches.
It's risky and potentially dangerous. Focus on safer and more code-compliant ways to provide power to your outlets. Start by understanding why* the outlets are wired the way they are now. Good luck, and be safe! Flag for review

Previous Question Next Question