Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Sandwich heater machine says (Max circuit requirement 40A), should i size breaker per that or by 125%

User: Cartoon1, Location: Florida

Asked on: Friday, September 27, 2024 at 2:52 pm EDT
Answered on: Thursday, March 6, 2025 at 3:04 am EST

Question: Hello. I have a Sandwich heater machine (Max circuit requirement 40A), should i size breaker per that or by 125%. I'm thinking of sizing the breaker by 1.25 to 50A, especially since the plug is rated for 50. But it also says (max circuit requirement is 40A) - im not sure if that means FLA or Maximum breaker. The wires will be rated for 50Amp anyways, but should i size the breaker for 40A or 50A?Thank you,

You're right to be cautious and ask! It's important to get this right for safety. Here's the breakdown of how to determine the correct breaker size

Understanding the Terms:
Max Circuit Requirement (40A)

This is likely indicating the
maximum continuous current the sandwich heater is expected to draw under normal operation. Think of it as the Full Load Amperage (FLA).

125% Rule

This is a common practice in electrical code to protect against continuous loads. A "continuous load" is defined as a load that operates for 3 hours or more at a time. If a load is continuous, the breaker and conductors need to be rated for 125% of the load.

Steps to Determine Breaker Size


Is it a Continuous Load?
The most important question is: Will this sandwich heater be used continuously for 3 hours or more?

If YES (Continuous Load)

You MUST apply the 125% rule.


If NO (Non-Continuous Load)

You generally don't need to apply the 125% rule (but always double-check local codes).2.

Calculate Breaker Size



Continuous Load

40A (Max Circuit Requirement)
1.25 = 50A

Non-Continuous Load

You
could use a 40A breaker, but since your plug is rated for 50A and your wiring is also rated for 50A, a 50A breaker could also be used.3.

Plug Rating

You're correct to consider the plug rating. Using a 50A plug suggests the appliance
could draw up to 50A (although the normal operating draw is expected to be less).4.

NEC Article 422.11(E)(3) - Fixed Electric Space-Heating Equipment

If the sandwitch maker uses a motor of 1/8 horsepower or larger, The overcurrent device shall not exceed 150 percent of the appliance's rated current.If the sandwitch maker uses a motor of 1/8 horsepower or smaller, The overcurrent device shall not exceed 20 amperes for 120-volt circuits or 15 amperes for 208- or 240-volt circuits.

Recommendation

Because you are not sure if the sandwich heater uses a motor 1/8 horsepower or larger, you have to take extra precaution. You should size the breaker to 20amps max

Important Considerations and Notes



Local Codes ALWAYS Prevail

This advice is general. Always consult your local electrical codes and a qualified electrician. They will have the final say and can assess your specific situation.

Manufacturer's Instructions

Refer to the sandwich heater's user manual or documentation. It may have specific breaker size recommendations.


Upsizing is Not Always Better

While it might seem safer to "go bigger," oversizing a breaker can be dangerous. It can allow the wiring to overheat without tripping the breaker, potentially leading to a fire. The breaker is there to protect the wiring.

Voltage is Important

Always verify the voltage requirements of the sandwich heater (e.g., 120V or 240V) and ensure your circuit matches.

In summary, you need to decide if the load is continuous. If it is, the calculation is simple: 40A
1.25 = 50A. However, due to the possibility of the sandwitch maker using a motor, please seek professional help to ensure the wire is protected. Flag for review

Previous Question Next Question