Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Wiring of Local Control Station for Motor

User: timm333, Location: Minneapolis, MN

Asked on: Sunday, September 29, 2024 at 1:27 pm EDT
Answered on: Thursday, March 6, 2025 at 3:08 am EST

Question: I am trying to figure out the wiring of local control station for direct-on-line (DOL) low voltage motor. The motor is controlled by magnetic starter and digital overload relay in MCC, and local control station in the field.The local control station has switches (“start”, “stop”, and “hand-off-auto”) which are sometimes wired in series and sometimes in parallel. If we have to communicate three signals (“Start”, “Stop”, “Auto Status”) from local control station to MCC and then from MCC to Remote-PLC: then should the three switches of local control station ((“start”, “stop”, “hand-off-auto”) be wired in parallel or in series? Thanks

Okay, let's break down the optimal wiring configuration for your local control station to achieve reliable communication of "Start," "Stop," and "Auto Status" signals to the MCC and ultimately to the Remote-PLC.

Understanding the Requirements Reliable Signals

The key goal is to get accurate, unambiguous signals representing the desired motor state back to the PLC.


Safety

The Stop button must reliably stop the motor, even if there are faults elsewhere in the system.

Flexibility

The Hand-Off-Auto switch needs to clearly indicate which mode the motor is in.


Remote PLC Control

The signals need to be passed to the Remote PLC.

Optimal Wiring Configuration: Parallel with Dedicated Wires


The best approach is to wire the switches in parallel, with dedicated wires for each signal ("Start", "Stop", "Auto Status"). Here's why: Start

The "Start" switch, when pressed, sends a signal to the MCC to energize the motor starter coil.


Stop

The "Stop" switch, when pressed, removes the signal to the MCC, de-energizing the motor starter coil. This must be a normally closed (NC) contact in the series of the coil.

Auto Status

The "Hand-Off-Auto" switch determines whether the motor is controlled by the local control station or by the remote PLC. This should provide a signal indicating whether the switch is in "Auto" position.

Detailed Wiring Diagram (Conceptual)

+---------------------+| Local Control Station |+---------------------+
+-------+| | Start |--- Signal to MCC "Start" Input| +-------+
+--------+| | Stop NC|--- Signal to MCC "Stop" Input (Normally Closed)| +--------+
+------------------+| | Hand-Off-Auto |--- Signal to MCC "Auto Status" Input| | (Auto Position)
+------------------+|+---------------------+
(Wires)V+-------+| MCC |+-------+
(Hardwired or Network)V+--------------+| Remote PLC |+--------------+
Explanation1. Start Circuit

Use a momentary normally open (NO) contact on the "Start" switch. When the "Start" button is pressed, the NO contact closes, sending a "Start" signal to a dedicated input on the MCC. The MCC uses this signal to energize the motor starter coil (possibly with latching logic).2.

Stop Circuit



Crucially
, use a normally closed (NC) contact on the "Stop" switch. The NC contact is wired in series with the motor starter coil circuit within the MCC. When the "Stop" button is pressed, the NC contact opens, immediately de-energizing the motor starter coil and stopping the motor. Also, send a "Stop" signal to a dedicated input on the MCC. This is primarily for PLC awareness of the stop event.3. Hand-Off-Auto Circuit

Use a selector switch with at least two positions: "Hand" (Local) and "Auto" (Remote). The "Auto" position closes a contact, sending an "Auto Status" signal to a dedicated input on the MCC. The MCC uses this signal to determine whether to allow the Remote PLC to control the motor (e.g., enable PLC start/stop commands). The "Hand" position opens the contact, indicating local control.4.

MCC Logic

The MCC uses the "Start," "Stop," and "Auto Status" signals to control the motor starter coil. It likely includes latching logic (using an auxiliary contact on the motor starter) to keep the motor running after the "Start" button is released. The MCC also communicates the motor status (running, stopped, fault) back to the Remote PLC.5.

Remote PLC

The Remote PLC monitors the motor status from the MCC. When in "Auto" mode, the Remote PLC sends "Start" and "Stop" commands to the MCC, which the MCC then uses to control the motor.

Advantages of Parallel/Dedicated Wiring
Clear Signals

Each signal has its own dedicated wire, eliminating ambiguity.

Fault Isolation

A problem with one switch or wire doesn't necessarily affect the others.


Easy Troubleshooting

Testing and diagnosing issues are much simpler.

Safety

The Stop button is hardwired to interrupt the circuit and is independent of any other switch.

Why Not Series Wiring?
Complexity

Series wiring can become confusing and difficult to troubleshoot.

Signal Interference

A fault in one switch can prevent other signals from being transmitted.


Less Reliable Stop

A break in the circuit for start signal can prevent the motor from starting, however a fault with Stop signal can render the stop functionality useless.

Important Considerations
Wiring Methods

Use appropriate wiring methods (conduit, cable trays, etc.) according to your local electrical codes.


Wire Gauges

Select wire gauges suitable for the voltage and current being carried.

Terminal Blocks

Use terminal blocks in the local control station and MCC for clean and organized wiring.


Documentation

Create detailed wiring diagrams and label all wires and terminals clearly.*

Safety Interlocks

Consider incorporating additional safety interlocks as needed (e.g., emergency stop buttons).

Example MCC Logic (Simplified)


The MCC logic might look something like this (using ladder logic concepts):
// Start LogicIF (MCC_Start_Button OR PLC_Start_Command) AND NOT Stop_Signal AND Auto_Status THENMotor_Starter_Coil = ON;ENDIF// Stop LogicIF Stop_Signal THENMotor_Starter_Coil = OFF;ENDIF
In summary, use parallel wiring with dedicated wires for your "Start," "Stop," and "Auto Status" signals. This will provide the most reliable, safe, and easy-to-troubleshoot solution for your local control station. Remember to consult with a qualified electrician to ensure that the wiring is done correctly and in accordance with all applicable electrical codes. Flag for review

Previous Question Next Question