Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Need 2nd opinion on Reliance Controls correspondence of 50A manual transfer switch questions

User: OhioIsEverywhere, Location: Ohio

Asked on: Sunday, September 29, 2024 at 2:35 pm EDT
Answered on: Thursday, March 6, 2025 at 3:08 am EST

Question: I recently purchased a Reliance Controls 50A manual transfer switch model A510C (https://www.reliancecontrols.com/pr...a-2-1p-20a-6-1p-15a-circuits-metal-gray-a510c) and had some concerns wiring it to the PB50 flanged power inlet (https://www.reliancecontrols.com/products/reliance-controls-pb-series-power-inlet-boxes-50-pb50). I noticed that the feed wires for the transfer switch are 10 gauge and they would not stay secure when inserted to the PB50 and screwed as far as I could without damaging the hex bolt or the trapezoidal bond that is pushed by the hex bolt. Everything I've found said that 10 gauge is not rated for greater than 30A (https://www.google.com/search?q=10+gauge+stranded+wire+amperage). I do see some exceptions like at different temperatures the rated amperage is a bit higher but nothing close to 50A. Also when searching what gauge wire I should be using for 50A service I find 6 gauge (https://www.google.com/search?q=10+gauge+stranded+wire+amperage). At this point I'm concerned about the 10 gauge wires not securing to the flanged inlet:https://imgur.com/JGHfFCX

You've identified a significant problem and your concerns are valid. Let's break down the issues and figure out how to address them

The Core Problem: Undersized Wiring for 50A
10 Gauge Wire is Not Rated for 50 Amps

You are absolutely correct. Generally, 10 gauge copper wire is rated for a maximum of 30 amps
under normal household wiring conditions. The exceptions at higher temperatures are for specific applications (like motor windings) and are not applicable to standard residential wiring and transfer switches. Using 10 gauge wire for a 50-amp circuit is a serious fire hazard.

Code Violation

Using undersized wiring is a violation of the National Electrical Code (NEC) and local building codes. This could invalidate your homeowner's insurance and create legal liabilities if a fire occurs.

Overheating Risk

The wire will overheat under a 50-amp load. This melts insulation, creates arcing, and is a prime cause of electrical fires.

Why the Reliance Transfer Switch Has 10 Gauge Wiring


This is a common point of confusion. The transfer switch is
rated for 50 amps, but it does not mean all the internal wiring is designed to carry 50 amps continuously. Here's the likely explanation: Circuit Distribution

The transfer switch likely distributes the 50-amp load across multiple circuits. It has (6) 15A circuits and (2) 20A circuits which are wired with 14 gauge and 12 gauge wires respectively. Therefore the 50A from the flanged inlet is not expected to be carried completely by the 10 gauge wires. They likely have a breaker for each circuit as well in case there is any overdraw from the circuits in the transfer switch.

Intermittent Use

It is expected that the generator will not be in use often so the 50A coming from the flanged inlet will not be supplied continuously for long stretches.


Input Wiring

The 10 gauge wires are for input. They expect you to run the output wiring yourself which should be appropriately gauged for the current rating.

The Connection Problem with the PB50 Inlet
Incompatible Wire Size

The lug terminals on the PB50 are designed to accept the correct gauge wire for a 50-amp circuit, which is typically 6 gauge copper. 10 gauge wire will be too small and will not make a secure and reliable connection. Your assessment that the hex bolt will not provide a secure bond is correct.


Potential for Loosening

An improperly secured connection is a high-resistance connection. This generates heat, further loosening the connection, and increasing the risk of arcing and fire.

What You MUST Do
1. STOP! Do Not Use the Transfer Switch in its Current Configuration. Using the transfer switch with undersized wiring is extremely dangerous.2. Replace the Input Wiring with appropriately gauged wiring

Run 6 gauge wire from the flanged inlet to the transfer switch.

Detailed Steps for Correct Wiring
1. Safety First

Turn off the main breaker in your electrical panel before working on any wiring. Verify the circuit is de-energized with a non-contact voltage tester.2.

Wire Size Calculation

For a 50-amp circuit, you need 6 gauge copper wire (THHN or THWN insulation is common).3.

Replacing the input wiring

You will need to remove the 10 gauge wires and run the 6 gauge wire to the flanged inlet. Be sure to follow any instructions for the transfer switch when running the wire.4.

Connecting to the PB50 Inlet

Loosen the terminal screws on the PB50 inlet. Insert the stripped ends of the 6 gauge wires into the terminals. Tighten the screws securely. Torque them to the manufacturer's specifications if available. A proper crimp connection is ideal for solid connections.

Important Considerations



Hire a Qualified Electrician

Unless you are very experienced with electrical wiring and comfortable working with high amperage circuits,

hire a licensed electrician
to do this work. It's not worth risking your safety or the safety of your home. A professional will ensure the installation is done correctly and safely, and will verify that it meets all local codes. Local Codes

Consult your local building codes and electrical inspector. They may have specific requirements for generator transfer switch installations.


Proper Tools

Use the correct tools for working with these wire sizes, including wire strippers, wire crimpers (for terminals), and a torque screwdriver (for tightening connections).

Wire Type

Use the correct type of wire (THHN/THWN) for the application and environment.


Strain Relief

Ensure proper strain relief for all wiring connections to prevent wires from being pulled out of the terminals.

In Summary


The 10 gauge wiring for the input on the Reliance transfer switch is inadequate for a 50-amp circuit. You must replace it with 6 gauge wire to ensure safe and compliant operation. Because electrical work is very dangerous, it is best to hire a qualified electrician to do the job to prevent damage or injury. Flag for review

Previous Question Next Question