Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: New Standby Emerg. Generator for a residence.

User: Luis De Castro, Location: Miami Fl.

Asked on: Monday, September 30, 2024 at 4:03 pm EDT
Answered on: Thursday, March 6, 2025 at 3:11 am EST

Question: Doing engineering plans for the installation. The generator is a new 60KW generac 120/240v single phase with floating neutral. I understand that is a non-separetely derived system. Is t ground rod required. The automatic transfer switch is a2p- 400a with a 400a circuit breaker main. already installed in the house. The generator breaker will be a 2p-300a. IM a little confused about thye grounding

Okay, let's break down the grounding requirements for your 60kW Generac generator installation. This is a common area of confusion, especially with floating neutral generators. I'll cover the key points and address your specific questions.

Understanding Separately Derived Systems (SDS) vs. Non-Separately Derived Systems (NDS)



Separately Derived System (SDS)

This is a generator where the neutral is
isolated from the utility neutral. It's essentially its own independent power source with its own neutral bonded to ground. Think of a transformer whose secondary is not directly connected to the primary.

SDSs
require a grounding electrode system (ground rod or equivalent) at the generator.
Non-Separately Derived System (NDS)

This is your situation. The generator's neutral is not isolated from the utility neutral. Instead it is floating. When the generator runs, it uses the neutral from the electric company. Think of a transformer where the secondary is directly connected to the primary.

NDSs do not require a grounding electrode system (ground rod or equivalent) at the generator.
Your Specific Situation (60kW Generac, Floating Neutral, NDS)

Because your Generac generator is:

Floating Neutral

This is the most important factor.


Non-Separately Derived

The neutral from the generator will connect to the neutral from the utility service via the automatic transfer switch (ATS).Therefore, the answer is:

NO, you do NOT need a ground rod or additional grounding electrode system at the generator itself.
Why No Ground Rod at the Generator (NDS)?

The reason you don't need a ground rod at the generator is that the grounding and bonding of the entire system is already handled at the main service entrance (where your utility meter is). The neutral and ground are bonded together at the service entrance, and that's where the grounding electrode system (ground rods, water pipe, etc.) is connected. You are relying on the existing grounding electrode system.

Grounding and Bonding Requirements (Still Critical)

Even though you don't need a ground rod at the generator, proper grounding and bonding are still absolutely crucial for safety. Here's what you do need to focus on:1.

Equipment Grounding Conductor (EGC)

This is the most important thing. You must run an equipment grounding conductor (typically a green or bare copper wire) from the generator's grounding lug to the automatic transfer switch (ATS). This EGC provides a low-impedance fault current path back to the service entrance, allowing the overcurrent protection (circuit breakers) to trip in the event of a fault.

Sizing the EGC

The size of this EGC must be determined according to the overcurrent protection device protecting the conductors from the generator to the ATS which in your case is a 300a circuit breaker at the generator. The EGC must comply with NEC Table 250.122. For a 300A overcurrent device, a #4 AWG copper conductor is typically required.
Confirm this based on the actual amperage of your generator breaker and the NEC table.2.

Bonding at the Generator

Ensure that all non-current-carrying metal parts of the generator (frame, enclosure, etc.) are properly bonded together and connected to the generator's grounding lug where the EGC lands.3.

Automatic Transfer Switch (ATS) Grounding

The ATS needs to have a grounding connection. Typically this is achieved because the metal case of the ATS is grounded through the metal conduit from the service entrance. If your ATS is not grounded in this manner, you must ground it using an appropiately sized conductor.4.

Neutral Connection at the ATS

The neutral from the generator and the neutral from the electric company should be wired properly at the automatic transfer switch. This is usually a straightforward connection, but double-check the ATS manufacturer's instructions.

Important Considerations and Potential Issues



Local Codes

Always check with your local electrical inspector or authority having jurisdiction (AHJ). They have the final say and may have specific requirements that go above and beyond the NEC.

Manufacturer's Instructions

Follow the generator and ATS manufacturer's instructions to the letter. They may have specific recommendations for grounding and bonding.


Conduit

If you use metal conduit between the generator and the ATS, the conduit can serve as the equipment grounding conductor if it is properly installed with listed fittings and provides a continuous, low-impedance path. However, it is always best practice to also run a dedicated EGC. This provides redundancy and ensures a reliable ground fault path.

Voltage Drop

Make sure the wiring between the generator and the ATS is sized correctly to minimize voltage drop, especially under full load. Longer runs will require larger wire. A 300A breaker requires very thick gauge wires.


Coordination

Make sure the breakers are selected to ensure proper coordination. The generator breaker should trip before the main house breaker.

Summary

Your floating neutral, non-separately derived generator does not require a ground rod at the generator location. A properly sized equipment grounding conductor (EGC) from the generator to the ATS is essential. Ensure all grounding and bonding connections are secure and comply with the NEC and local codes. Follow the manufacturer's instructions for both the generator and the ATS. Consult with a qualified electrician to review your plans and perform the installation.

Disclaimer:
I am an AI Chatbot and cannot provide professional electrical advice. This information is for educational purposes only. Consult with a licensed and qualified electrician for all electrical work.* Flag for review

Previous Question Next Question