Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: UL listings panel lugs

User: Dad7x7, Location: Tennessee 37862

Asked on: Monday, September 30, 2024 at 5:35 pm EDT
Answered on: Thursday, March 6, 2025 at 3:12 am EST

Question: Do Mechanical lugs for feeders . have to be OEM in order to not void the UL listing?If so, what would you do if you needed to do a panel change-out and the OEM lugs were backordered ? The generic ones are the same size and rating, and of course UL rated .

Okay, let's break down the issue of mechanical lugs and UL listing in the context of a panel change-out.

Do Mechanical Lugs Have to Be OEM to Maintain UL Listing? Generally, No, but with a HUGE Caveat

Simply put, no. You are generally allowed to use non-OEM lugs.


The Caveat: UL 67 (Panelboards) and UL 508A (Industrial Control Panels) Follow Instructions
Panelboards and control panels are UL Listed based on their intended design. The manufacturer will usually provide instructions for how to properly terminate conductors, and using listed non-OEM lugs that are compliant with those instructions should suffice. UL 67

If the panelboard specifically requires UL 67 Listed lugs, then you must use UL 67 Listed lugs that also meet the size and material requirements of the panel. UL 67 covers panelboards.
UL 508A

If the panelboard is installed in an industrial control panel, UL 508A applies. Follow the instructions to determine the required rating and construction of the lugs.

The Key is Suitability and Compatibility

The non-OEM lug
must be suitable for the application. This means:

UL Listed for the Purpose

The lug must be UL listed (or another nationally recognized testing laboratory - NRTL - listed) for connecting conductors in electrical equipment. The listing should be clearly marked on the lug.

Proper Size and Ampacity

The lug's conductor size range and ampacity must match or exceed the requirements of the circuit it's being used on. It has to be able to handle the fault current.


Material Compatibility

The lug's material (usually aluminum or copper/alloy) must be compatible with the conductor material (copper or aluminum). Dissimilar metals can cause corrosion and failures.

Proper Installation

The lug must be installed according to its manufacturer's instructions, using the correct torque values and methods.


Why the Concern About OEM?
The manufacturer of the panelboard obtained its UL listing based on a specific design, and the panelboard was tested with particular components. Using a non-OEM lug could technically invalidate the original listing if it's determined that the non-OEM lug alters the panel's performance or safety characteristics in a way that violates the UL standard. However, simply being non-OEM isn't automatically a violation.

What to Do When OEM Lugs Are Backordered

This is a very common scenario! Here's a practical approach:1.

Consult the Panel Manufacturer's Documentation

Before doing anything, carefully review the panel manufacturer's installation instructions, wiring diagrams, and any other documentation that came with the panel. Look for specific requirements or recommendations regarding lug types, sizes, materials, or torque values. The manufacturer may even list acceptable alternatives or brands.2.

Choose a Suitable UL-Listed Replacement



Verify Listing

Select a lug that is UL Listed for use in electrical equipment.

Check Size and Rating

Ensure the lug's wire range and ampacity are equal to or greater than the original lug. The conductor size range is critical. If the lug is too big and you have to use reducer inserts, the AHJ may reject the install.


Material Compatibility

Match the lug material to the conductor material. Copper or copper alloy lugs for copper conductors; aluminum or dual-rated lugs for aluminum conductors.

Short-Circuit Current Rating (SCCR)

This is very important. Make sure the lugs have a Short-Circuit Current Rating high enough to handle the system's potential fault current. Your Electrical Engineer should provide this to you.


Torque Requirements

Ensure the lugs are listed for the proper torque.

Consult the AHJ

Some areas have specific requirements regarding lug types. You may need to check with the Authority Having Jurisdiction before proceeding.3.

Document Your Actions



Record the OEM Lug Information

Note the manufacturer, part number, and specifications of the original lug. Take pictures.

Record the Replacement Lug Information

Note the manufacturer, part number, UL listing number, wire range, ampacity, material, and installation instructions of the replacement lug. Take pictures.


Photograph the Installation

Take clear pictures of the installed replacement lug, showing its location and connection to the conductor.4.

Communicate with the Inspector/AHJ



Be Proactive

Before the inspection, inform the electrical inspector (AHJ) that you used a non-OEM lug due to supply chain issues.


Provide Documentation

Show the inspector the documentation you compiled in step 3. Explain how the replacement lug meets or exceeds the requirements of the original lug and the applicable codes and standards.

Be Prepared to Justify Your Choice

Be ready to explain why you believe the replacement lug is a suitable and safe alternative.5.

Proper Installation is Paramount



Follow Lug Manufacturer's Instructions

Carefully follow the lug manufacturer's installation instructions, including using the correct torque wrench and torque values.

Clean the Conductors

Thoroughly clean the conductors before inserting them into the lug. Use an anti-oxidant compound (e.g., NOALOX) if required by the lug manufacturer or conductor type.


Inspect the Connection

After tightening the lug, visually inspect the connection to ensure it's secure and that the conductor is properly seated.

Key Considerations



UL's "Field Modification" Guidance

UL has guidance on field modifications to listed equipment. Generally,
minor modifications that don't significantly alter the equipment's safety characteristics are permissible. Replacing a lug with a suitable, listed equivalent likely falls into this category if done properly.

AHJ's Discretion

Ultimately, the AHJ has the final say on whether the installation is acceptable. Their interpretation of the NEC and local codes will prevail.*

Engineer of Record (if applicable)

If the project has an Engineer of Record, consult with them. They might have specific requirements or pre-approved alternatives.

In summary:
You can use non-OEM lugs if they are properly listed and are suitable for the application. Document everything and be prepared to discuss your decisions with the AHJ. Taking these steps should help you ensure a safe and code-compliant installation. Flag for review

Previous Question Next Question