Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Service Calculation for EV Charger

User: yargnits67, Location: Space Coast FL

Asked on: Monday, September 30, 2024 at 6:58 pm EDT
Answered on: Thursday, March 6, 2025 at 3:12 am EST

Question: Hello folks,I am trying to determine if I can add an EV charger in my garage. I'm just learning about calculating load and came up with the following by looking at my breaker panel in the garage:House 2626sqft: = 7878A/C: 50 amp = 4800Range: 40 amp = 3840A/H: 35 amp = 3360W/H/Dryer: 30 amp = 576020 amp (11) = 2112015 amp (10) = 14400Total = 61158 / 240 / 1.732 = 148ampsPanel outside of house where electricity enters home:Pool: 30amp = 5760Irrigation: 30amp = 5760Grand total = 72,678 / 240/ 1.732 = 175amps.I have a 200amp service and I've read I need to maintain no more than 80%.I would like to install a 50amp EV charger but I'm already over the 80%.I'm hoping because I have zero clue what I am talking about and doing that I did some calculation wrong.Thanks,Joe

Okay, Joe, you're right – you're on the right track in trying to calculate the load, but the way you're doing it is going to massively over-estimate your actual load. Here's a breakdown of where you're going wrong and how to approach this more realistically

Key Concepts:
Demand Factor

You're calculating the
maximum possible load if everything was running at full capacity simultaneously. This never happens in a real house. Demand factors are percentages that account for the fact that you won't use all your appliances at the same time at their maximum rating.

Continuous Load

An EV charger is considered a continuous load because it will draw a significant amount of power for three hours or more. Because of this NEC mandates that the breaker be sized at 125% the amount you plan to draw. For example, a 40amp charger must have a 50amp breaker.

Code Requirements (NEC)

The National Electrical Code (NEC) has specific rules for calculating service load. You can't just add up all the breaker sizes. It's based on square footage, fixed appliances, and then demand factors applied to general use circuits.


Voltage

Single phase is calculated at 240v in US homes. I see you have 1.732 used as a voltage calculation. This is for 3 phase electrical, so this is not correct.

Where Your Calculations Go Wrong


Square Footage

Your square footage calculation is okay. NEC requires 3 volt-amps per square foot. You can add this to the general lighting load. So 2626 sqft 3 volt amps = 7878 VA.2.

Air Conditioning

Using the breaker size directly converted to VA (volts x amps = watts/VA) overestimates the actual load. You should be using the nameplate rating on the A/C unit itself (the label on the unit that gives voltage, amperage, and wattage). Look for the "Maximum Overcurrent Protection" or "Minimum Circuit Ampacity" on the nameplate, as that's the actual load the breaker protects against, not the full amperage of the breaker.3.

Range

Similar to A/C, using the breaker size isn't accurate. The NEC allows for demand factors on ranges. You don't just take the full wattage.4.

Water Heater/Dryer

Again, demand factors apply. You won't use both at the same time (usually).5.

20A and 15A Circuits

This is the biggest source of error. You are assuming every single outlet on those circuits is being used to its maximum capacity, which is impossible. You cannot just add up the total amperage of all the breakers.6.

Outside Panel Loads

Pools and irrigation also have demand factors, and are often not run concurrently.

How to Calculate Load More Accurately

Here's a simplified overview (refer to NEC Article 220 for full details):1.

General Lighting Load

3 VA per square foot (you've already done this).
2626 sqft 3 VA/sqft = 7878 VA2.

Small Appliance Branch Circuits

Two 20-amp circuits for kitchen/dining areas (required by code). Calculate as 1500 VA per circuit, total 3000 VA.3.

Laundry Circuit

One 20-amp circuit dedicated to the laundry area (required by code). Calculate as 1500 VA.4.

Fixed Appliances



Range

This is tricky, as it uses NEC Table 220.55. Look at the nameplate rating of your range (in watts or VA). Then consult Table 220.55 to find the appropriate demand factor. For example, if your range is rated at 12kW (12,000 VA), the demand factor might be 8kW. The table varies depending on the number and wattage of cooking appliances.

Water Heater

Use the nameplate wattage.


Dryer

Use the nameplate wattage.

A/C

Use the nameplate rating (VA or watts) of the compressor unit – this is the biggest draw. Include the fan motor as well.


Pool

Use the nameplate rating of the pool pump and any heating elements.

Irrigation

Use the nameplate rating of the pump.5.

Other Circuits

This is where it gets subjective. You can't just add up all the breakers. You need to estimate the
typical load on these circuits. This is where experience and knowledge of your usage patterns come in. A conservative approach is to count each general-purpose receptacle as 180 VA (this is an NEC guideline for commercial buildings, but can be a starting point). Then, estimate how many of those receptacles are likely to be in use at any given time and what they'll be powering.

Example Simplified Calculation

Let's say you have these values (after looking at nameplates and estimating):
General Lighting: 7878 VA Small Appliance Circuits: 3000 VA Laundry Circuit: 1500 VA Range (after demand factor): 8000 VA Water Heater: 4500 VA Dryer: 5000 VA A/C: 4000 VA Pool: 2000 VA Irrigation: 1500 VA Other Circuits (estimated): 3000 VA

Total: 40,378 VA
Amps

40,378 VA / 240V = 168.24 amps

Adding the EV Charger

A 50 amp EV charger will draw 40 amps continuously (80% of the breaker rating). This is because per NEC a continuous load needs to be sized at 125% of the rating so a 40amp draw requires a 50amp breaker.

EV Charger Load

40 amps 240V = 9600 VA

New Total

40,378 VA + 9600 VA = 49,978 VA

New Amps

49,978 VA / 240V = 208.24 amps

Important Considerations



80% Rule

Your 200-amp service should ideally not exceed 80% of its capacity continuously. That's 160 amps.

Load Management

EV chargers can often be configured to reduce their charging current. You could set the charger to 32 amps (requiring a 40 amp breaker), reducing the load.


Professional Load Calculation

This is crucial. A licensed electrician can perform a proper load calculation, taking into account all the relevant factors and local codes. They will use specialized tools and knowledge to make accurate assessments.

Load Shedding

Some advanced EV chargers or smart home systems can "shed" load during peak usage. This means the charger will automatically reduce its charging rate if other high-demand appliances are running, preventing you from exceeding your service capacity.


Panel Upgrade

If the load calculation (even by a professional) shows you're exceeding capacity, you'll need to consider upgrading your service panel to a higher amperage (e.g., 250A or 300A). This is a significant expense but may be necessary.

What to Do Next


Gather Data

Find the nameplate ratings for all of your major appliances (A/C, range, water heater, dryer, pool pump, etc.).2.

Estimate Usage

Think about how you typically use your appliances. Are you likely to be running the A/C at full blast while simultaneously using the range, dryer, and charging an EV?3.

Hire an Electrician:
A qualified electrician is your best resource. They can: Perform an accurate load calculation. Assess your existing wiring and panel. Advise on the best charging solution for your needs and electrical capacity. Install the EV charger safely and according to code.Don't guess or take shortcuts when it comes to electrical work. It's a safety issue and can be expensive to correct if done improperly. Flag for review

Previous Question Next Question