Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Utility Transformer feeding power distribution box, feeding three transformers. Are ground rods needed at each transformer

User: Greenautomator, Location: United States

Asked on: Tuesday, October 1, 2024 at 10:43 am EDT
Answered on: Thursday, March 6, 2025 at 3:14 am EST

Question: This is for an EV site, a utility transformer is feeding a 2000 amp discount.Main bond jumper installed here tied to 2 ground rods.The 2000 amp disconnect feeds 8 450A disconnects.Each feed to a 480V 400A fused disconnect.Each 400A fused disconnect feeds a 167KVA transformer 480V single phase primary to 240/120V single phase secondary.Each Transformer feeds 2 120/240 branch 400A branch panels, each having 4 2 pole 100A breakers for EV chargers.EV's together are limited to 320AQuestion is if each of these transformers need its own ground rod?

Okay, let's break down the grounding requirements for this EV charging system. The short answer is Yes, the 167kVA transformers likely need their own grounding electrode system (typically a ground rod or other approved electrode), but there are some nuances and exceptions.Here's the reasoning, based on the National Electrical Code (NEC), which is the standard we'll use

NEC Considerations

1. Separately Derived System (SDS)

Each 167kVA transformer creates a Separately Derived System (SDS). An SDS is defined as an electrical system whose power is derived from a source other than a service. Since your transformers create a new 240/120V system from the 480V supply, they fall under this definition.2.

Grounding Requirements for SDS (NEC 250.30)

NEC Article 250.30 outlines the grounding requirements for SDS. Key points from this section:

(A) Grounded Conductor Connection

The neutral (grounded conductor) of the 240/120V secondary
must be connected to a grounding electrode conductor (GEC). This provides a low-impedance path for fault current back to the source, allowing overcurrent protection devices to operate.

(A)(1) Location.
The location of the grounding connection should be at the nearest point of neutral of the source transformer, or as close as possible. (A)(2) Size and Material. The ground wire from the source to the rod should be sized according to NEC 250.66 (A)(3) Grounding Electrode Conductor. The GEC connects the neutral to the grounding electrode. (A)(4) Grounding Electrode. The GEC must connect to one of the following: Nearest effectively grounded structural metal of the building or structure Nearest effectively grounded metal water pipe. Other electrodes as specified by the NEC, including ground rods. (A)(5) Bonding of Electrodes

All grounding electrodes that are present at the building or structure must be bonded together, regardless of whether or not they are also being used to ground an SDS. This ensures that all parts of the grounding system are at the same potential.3.

Why the Transformers Need Separate Grounding

Without their own grounding electrode system, a ground fault on the 240/120V side of the transformer would have to travel all the way back to the main 2000A disconnect's ground rods to find a path to ground. This long path increases impedance, hindering the ability of the overcurrent protection (breakers in the panel) to quickly clear the fault. Additionally, the increased impedance could result in elevated touch potentials and increased risk of electric shock.

Grounding Electrode System (GES) for Each Transformer (NEC 250.50 - 250.70)



Ground Rod(s)

The most common and often easiest solution is to install one or more ground rods (typically two, spaced at least 6 feet apart) at each transformer location.

Other Electrodes

As mentioned above, the NEC allows for other grounding electrodes, such as connection to the building's structural steel or a metallic water pipe system (under certain conditions). However, these are less common for transformer applications unless readily available and compliant with NEC requirements.

Important Considerations and Exceptions



Engineering Study

A qualified electrical engineer could perform a detailed study of the system to determine if a different grounding scheme is acceptable. However, this is rarely cost-effective for systems like this.

Local Amendments

Always check with your local electrical inspector for any local amendments to the NEC. Some jurisdictions have specific requirements for grounding EV charging installations.


Professional Consultation

This information is for general guidance only. It is essential to consult with a licensed electrical engineer and/or a qualified electrician to design and install the grounding system for your EV charging station. They can assess the specific site conditions, perform necessary calculations, and ensure compliance with all applicable codes and regulations.

Resistance to Ground

Aim to have a ground resistance of 25 ohms or less at each transformer location. If a single ground rod exceeds this value, you
must install a second ground rod and bond it to the first.

Summary:


For safety and code compliance, each 167kVA transformer in your EV charging system
most likely* needs its own grounding electrode system (typically two ground rods). This provides a low-impedance path for ground faults, ensuring the rapid operation of overcurrent protection and minimizing the risk of electrical shock. Always consult with qualified professionals to design and install the grounding system according to the NEC and local codes. Flag for review

Previous Question Next Question