Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Sizing Feeder for ADU (Accessory Dwelling Unit)

User: Will Wire, Location: California: NEC 2020

Asked on: Wednesday, October 2, 2024 at 9:49 am EDT
Answered on: Thursday, March 6, 2025 at 3:17 am EST

Question: Is it code compliant to apply demand factors for sizing the feeder for an ADU (Accessory Dwelling Unit), such as first 10,000 VA @ 100%, the remainder at 40%, etc?Thank you,Trent

Yes, generally, it is code-compliant to apply demand factors for sizing the feeder for an ADU, as long as it's done in accordance with the applicable electrical code. The specific code language and allowable demand factors vary depending on the jurisdiction and the specific characteristics of the ADU. Here's a breakdown of the key considerations

National Electrical Code (NEC) - Key Sections
Article 220: Branch-Circuit, Feeder, and Service Calculations

This is the
foundation for all load calculations, including for ADUs. It provides the general rules and specific demand factors for various types of loads.

220.12 Dwelling Unit Feeder and Service Loads

This section covers the general lighting and receptacle load calculations, typically using 3 VA per square foot.

220.53 Small Appliance and Laundry Loads - Dwelling Unit

Requires the addition of 1500 VA for each small appliance branch circuit (usually two required) and 1500 VA for the laundry circuit.


220.55 Table 220.55 Demand Factors for Household Electric Ranges, Wall-Mounted Ovens, Counter-Mounted Cooking Units, and Other Household Cooking Appliances over 1 ¾ kW Rating

This table is crucial for calculating the demand load for cooking appliances. It allows for significant demand reduction based on the number and rating of cooking appliances.

220.61 Optional Calculation - Dwelling Unit

This is
often the most advantageous method for ADUs, allowing for a more realistic assessment of actual demand. This section often uses the "first 10 kVA at 100%, remainder at 40%" approach you mentioned.

Important Considerations and Code Requirements


Local Amendments

Always check with your local electrical inspector or building department. Local jurisdictions often amend the NEC, adding or modifying requirements. They may have specific rules for ADUs.2.

Optional Calculation vs. Standard Calculation

The NEC allows for either a standard calculation (Article 220 Part III) or an optional calculation (Article 220 Part IV). The optional calculation
generally results in a lower calculated load, which can significantly impact feeder size. However, the optional calculation is subject to specific rules and may not always be permitted (e.g., if the total connected load is unusually high).3.

Heating and Cooling

The NEC requires you to include the
larger of the heating or cooling load at 100%. This can be a significant factor. If using electric heat, the load will be substantial.4.

Appliances

Permanently connected appliances (e.g., water heater, dishwasher, garbage disposal) must be included in the load calculation.5.

Nameplate Ratings

Always use the nameplate rating of appliances when performing load calculations.6.

Demand Factors

Demand factors are multipliers applied to the connected load to estimate the
likely maximum demand at any given time. The NEC provides various tables and rules for applying demand factors. The goal is to avoid oversizing the feeder based on infrequent peak loads.7.

Continuous Loads

Circuits and feeders must be sized to handle continuous loads (loads expected to operate for 3 hours or more) at 125% of their rating.8.

Ampacity of Conductors

Once you've calculated the required feeder current, you must select conductors with sufficient ampacity, taking into account temperature correction and adjustment factors (e.g., for multiple conductors in a raceway).

Example Scenario and "First 10,000 VA at 100%, Remainder at 40%"


Let's say you're using the
optional calculation (220.61) for a dwelling unit. The code might say something like: General lighting and receptacles: 3 VA per square foot Two small appliance circuits: 1500 VA each = 3000 VA One laundry circuit: 1500 VA Electric range: 8000 VA (nameplate) Electric water heater: 4500 VA (nameplate) Air conditioner: 3000 VA (nameplate) Electric Baseboard Heaters: 5000 VA (nameplate)1. Calculate the Connected Load

Lighting/Receptacles (assume 1000 sq ft): 3 VA/sq ft 1000 sq ft = 3000 VA Small Appliance Circuits: 3000 VA Laundry Circuit: 1500 VA Range: 8000 VA Water Heater: 4500 VA Air Conditioner: 3000 VA Electric Baseboard Heaters: 5000 VA

Total Connected Load: 28,000 VA
2. Apply Demand Factors (using the "optional" method, and assuming the heater load is larger than the AC load)

First 10,000 VA @ 100%: 10,000 VA 1.0 = 10,000 VA Remaining 18,000 VA @ 40%: 18,000 VA 0.4 = 7,200 VA

Calculated Demand Load: 17,200 VA
3. Calculate Feeder Current

Assuming 240V supply: 17,200 VA / 240V = 71.67 Amps4.

Size the Feeder Conductors and Overcurrent Protection

You would need to select conductors rated for at least 71.67 Amps, after applying any temperature correction or adjustment factors. THHN conductors in conduit at 75°C may be appropriate. You would then select the next standard size overcurrent protection device (circuit breaker or fuse). For example, an 80-amp breaker.

Key Takeaways
Demand factors are essential for accurately sizing ADU feeders. Use the NEC as your guide, but always check with your local electrical inspector. The optional calculation method (Article 220.61) can often result in a smaller feeder size. Heating and cooling loads have a significant impact. Understand the difference between connected load and demand load.* Don't forget about continuous loads and conductor ampacity derating.

Disclaimer: I am an AI chatbot and cannot provide electrical design advice. Consult with a licensed electrical contractor or engineer for code-compliant designs specific to your project and jurisdiction. Incorrect electrical work can be dangerous and violate code requirements. Flag for review

Previous Question Next Question