User: overdriv, Location: IL
Asked on: Wednesday, October 2, 2024 at 4:31 pm EDT
Answered on: Thursday, March 6, 2025 at 3:18 am EST
Question: I have a Generac 20KW generator with a john deere diesel engine. It has a Deep Sea controller. On the cabinet with the controller is a round, red Estop push/pull type switch. I think it is going bad as once in awhile the controller will alarm that generator is locked out. If I cycle the switch a few times the alarm will reset and generator will again run on weekly schedule. Can online?n I buy this switch online?Also, the after the weekly scheduled run and after engine has cooled down to ambient, an alarm; "Low Coolant Temperature"will drop, alarm will sound. Alarm will clear, but engine will not start with that alarm down. Could this be a defective coolant temp sensor on the engine?I'm just a homeowner who bought and installed a Generac SD020 genset that was surplus from a cell tower.Any help would be appreciated.
Okay, let's address these issues with your Generac 20KW diesel generator
1. Estop Switch (Emergency Stop Switch)
You can almost certainly buy a replacement online. The trick is finding the exact replacement. Here's how to proceed: Identify the Switch
Look closely at the existing switch. There should be some markings on it:
Manufacturer
(e.g., Allen-Bradley, Eaton, Kraus & Naimer, Square D, etc.)
Part Number
This is the most important piece of information. It will be stamped or printed on the switch body.
Electrical Ratings
(Voltage and Current) - Usually expressed as VAC and Amps.
Search Online
Use the manufacturer and part number in your search. Try these online retailers:
Amazon
Often has a surprising variety of industrial electrical components.
eBay
Good for finding NOS (New Old Stock) or used parts.
Grainger
Industrial supply company.
McMaster-Carr
Wide selection of industrial components.
AutomationDirect
Specializes in industrial automation and control.
Generac Parts Suppliers
Search for companies specializing in Generac generator parts.
If No Part Number
If you can't find a part number, try searching by manufacturer and a description of the switch (e.g., "Allen-Bradley red mushroom head push pull Estop switch").
Key Considerations When Purchasing
Voltage and Current Rating
Make sure the replacement switch meets or exceeds the electrical ratings of the original.
Contact Configuration
This refers to how the switch contacts are wired (Normally Open, Normally Closed, etc.). It's critical that the replacement has the same configuration as the original. The wiring diagram for the generator will help.
Physical Size and Mounting
Ensure the replacement switch fits the existing hole and mounts securely.
IP Rating
Consider the IP rating (Ingress Protection) if the generator is exposed to the elements. A higher IP rating means better protection against dust and water.
Temporary Fix (Use with extreme caution and only for testing)
As a temporary measure to confirm the switch is the problem, you could bypass the switch by disconnecting the wires from it and connecting them together.
However, this completely removes the emergency stop functionality, which is a critical safety feature. Do not operate the generator unattended with the Estop bypassed. This is purely for troubleshooting to confirm the switch is the culprit.2. "Low Coolant Temperature" Alarm Likely a Defective Coolant Temperature Sensor
This is the most probable cause, especially if the engine is actually at ambient temperature.
Troubleshooting Steps
Visual Inspection
Check the wiring to the coolant temperature sensor. Look for loose connections, corrosion, or damaged wires. Clean and tighten any suspect connections.2.
Sensor Location
Locate the coolant temperature sensor on the engine. It's typically screwed into the engine block or cylinder head near the coolant passages.3.
Sensor Testing (Requires a Multimeter)
Resistance Check
Disconnect the sensor's electrical connector. Use a multimeter to measure the resistance across the sensor's terminals. Compare the measured resistance to the sensor's specifications (if you can find them). Often, the resistance will change significantly with temperature. A sensor that reads open circuit or short circuit at room temperature is likely bad.
Voltage Check
With the sensor connected, backprobe the sensor connector with a multimeter to check the voltage signal the sensor is sending to the controller. Compare the voltage to expected values, or if the specifications cannot be found, compare the voltages during a successful run and post alarm state.4.
Sensor Replacement
If the sensor tests bad, replace it with the correct part. Again, find the part number on the existing sensor.5.
Check Coolant Level
While unlikely if the alarm is "low temperature," double-check the coolant level in the radiator and overflow tank. A very low coolant level could cause inaccurate temperature readings.6.
Sensor Calibration
Some Deep Sea controllers can be calibrated. Consult the Deep Sea manual for your controller model to check if sensor calibration is possible, and what the correct parameters are.
Finding a Replacement Sensor
John Deere Parts Dealer
Your best bet for getting the exact correct sensor. Give them the engine model and serial number.
Generac Parts Suppliers
Some may carry John Deere engine parts.
Online Retailers
Search for the sensor by its part number.
Important Safety Considerations
Disconnect Power
Before working on any electrical components, disconnect the generator's battery and any external power sources.
Consult Manuals
Refer to the Generac generator manual, the John Deere engine manual, and the Deep Sea controller manual for specific troubleshooting procedures, wiring diagrams, and safety information.
Qualified Technician
If you are not comfortable working on electrical or mechanical systems, consult a qualified generator technician.
Troubleshooting Tips
Document Everything
Keep a detailed record of your troubleshooting steps, test results, and any changes you make. This will help you track your progress and communicate effectively with a technician if needed.
Take Pictures
Take pictures of wiring connections and component locations before disconnecting anything. This will help you reassemble everything correctly.
Use the Deep Sea Controller Display: Pay close attention to the Deep Sea controller display. It should provide valuable information about the generator's status and any active alarms.Let me know if you can find the part numbers for the Estop switch and the coolant temperature sensor, and I can help you find replacements. Good luck! Flag for review