Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Code of the day protecting nm cable in conduit

User: Jpflex, Location: Victorville

Asked on: Wednesday, October 2, 2024 at 8:47 pm EDT
Answered on: Thursday, March 6, 2025 at 3:20 am EST

Question: Regarding the code of the day, the NEC book to my knowledge failed to address calculations for max conduit fill when nm cable is ran inside conduit. Obviously the nm cable sheathing takes up more space than the insulated conductors and shouldn't be calculated with only conductor diameter as typical.However one book I came across said to measure the diameter of the nm cable jacket sheath and treat this as one conductor (percent fill table) when determining max conduit fill for nm cables. Is this correct?

You are correct, the NEC doesn't explicitly provide a specific calculation method for NM cable in conduit for fill. It's a common point of confusion and a gap in the code.The method of treating the NM cable as a single conductor based on the outer diameter of the cable sheath is a widely accepted and often recommended practice.

Here's a breakdown of why and what to consider: NEC's Silence

The NEC doesn't forbid NM cable in conduit in many situations (see further notes on suitability below), but it does lack specific instructions on how to calculate fill for this situation.


Why It's Reasonable

The NM cable's sheathing encompasses all the conductors, so the outer diameter of the cable is what occupies the space inside the conduit. Therefore, treating the entire cable assembly as one conductor with that outer diameter is logical. This is a pragmatic approach to account for the sheathing's space.

How to Apply


Measure the Outer Diameter

Accurately measure the outer diameter of the NM cable's sheathing. Use calipers for the most accurate measurement. If calipers aren't available, carefully measure with a ruler, ensuring you get the widest point.2.

Treat as a Single Conductor

Use this diameter as if it were the diameter of a single conductor.3.

Use NEC Chapter 9, Table 4 or Annex C

Refer to the appropriate conduit fill tables in NEC Chapter 9, Table 4 (for new conduit) or Annex C (for existing conduit), based on the type of conduit you are using. Calculate the allowable fill for the conduit size.4.

Calculate the Area

Calculate the area of the NM cable using the formula for the area of a circle: Area = π
(radius)^2, where radius is half the measured diameter.5.

Compare

Ensure the area of the NM cable is less than or equal to the allowable fill percentage for the conduit size.

Important Considerations



Suitability

While the NEC doesn't prohibit NM cable in conduit in general, consider the specific application. NM cable is intended for dry locations. Running it in conduit in wet or damp locations can be problematic due to potential condensation within the conduit. The 2023 NEC has increased the requirements for using NM cable in outdoor or wet location raceways, often requiring it to be rated for the environment. If you are going to install NM cable in a conduit underground you need to verify the product is rated for wet location use.

Derating

If you are putting multiple current carrying conductors inside a raceway, including NM cable with multiple current carrying conductors, you may need to derate the ampacity of the conductors, in accordance with NEC 310.15.


Ease of Pulling

Don't overfill! While the calculated fill may be within the NEC limits, exceeding about 40% fill can make pulling the NM cable extremely difficult, potentially damaging the cable sheathing. Consider upsizing the conduit if the calculated fill is nearing the maximum allowed.

Manufacturer Instructions

Always check the manufacturer's instructions for both the NM cable and the conduit. They may have specific recommendations or limitations.


Local AHJ

Ultimately, the Authority Having Jurisdiction (AHJ) has the final say. It's wise to discuss this approach with your local electrical inspector before starting the work to ensure they approve of the method.

In Summary

Yes, treating the NM cable as a single conductor based on its outer diameter is a commonly used and reasonable approach for calculating conduit fill when the NEC lacks explicit guidance. However, always consider the suitability of NM cable for the environment, the ease of installation, and consult with the AHJ.

Example:


Let's say you want to run a single 12/2 NM-B cable in a 1/2" EMT conduit.1. You measure the outer diameter of the 12/2 NM-B cable and find it to be 0.40 inches.
2. You treat this as a single conductor with a diameter of 0.40 inches.
3. From NEC Chapter 9, Table 4, the allowable fill for a 1/2" EMT conduit with one conductor is 53%. The area of 1/2" EMT is 0.304 in^2.
4. Calculate the area of the NM cable: Area = π (0.40/2)^2 = π (0.2)^2 = 0.1256 in^25. Compare: 0.1256 in^2 is less than 0.304 in^2, so the fill is acceptable according to the code.Even though the fill may be within the NEC limits, it is still good practice to upsize conduit if the fill comes close to the maximum limit. Flag for review

Previous Question Next Question