Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: What to do after hurricane Helene

User: Roger9, Location: Tampa

Asked on: Thursday, October 3, 2024 at 7:37 pm EDT
Answered on: Thursday, March 6, 2025 at 3:24 am EST

Question: I’m unsure about a problem we’re facing over here in Florida. We’re getting calls to houses that were flooded due to hurricane Helene. receptacle's and some switches were submerged in salt water. Nobody can really get an answer from the county or inspectors on what needs to be done.We know that any device or metal box that was submerged needs to be replaced but what do you guys think about the wire? If it’s cloth we’re replacing but we’re unsure about romex.

This is a tough situation, and I understand your concern. Dealing with saltwater intrusion after a hurricane is a serious issue when it comes to electrical safety. Here's my take, combining code considerations, practical experience, and risk mitigation

The Big Picture: Saltwater is Highly Corrosive and Conductive
Corrosion

Saltwater is incredibly corrosive. It will attack metal components, including the copper conductors in Romex, the terminals in devices, and the metal boxes. This corrosion can weaken the connections, increase resistance, and eventually lead to failures.


Conductivity

Saltwater is a good conductor of electricity. Even after the water recedes, residual salt can create conductive paths, leading to leakage currents, ground faults, and increased risk of shock or fire.

Romex (NM Cable) Considerations


Here's where it gets tricky. The NEC doesn't have a specific, explicit rule saying "all Romex submerged in saltwater must be replaced." However, we have to apply sound judgment and err on the side of safety. Here's how I'd approach it:1. Severity of Immersion and Duration



How deep was the water?
If the Romex was only briefly splashed, the risk is lower than if it was submerged for days. How long was it submerged? The longer the exposure, the greater the potential for corrosion and salt absorption. Was the Romex physically damaged by debris during the storm? Any visible damage is an immediate reason for replacement.2. Accessibility for Inspection



Can you fully inspect the Romex along its entire length?
If it's hidden behind walls, floors, or ceilings, a complete visual inspection is impossible. Can you test the insulation resistance of the Romex? A megohmmeter (megger) can be used to test the insulation integrity. This is highly recommended. A low insulation resistance reading indicates a compromised cable.3. Age and Condition of the Romex



How old is the wiring?
Older Romex might have insulation that is more brittle or susceptible to degradation. Was the Romex already showing signs of wear or damage before the flood?Recommendations Best Practice: Replace Romex Submerged in Saltwater, Especially if Prolonged

In my professional opinion, the safest and most responsible approach is to replace any Romex that was submerged in saltwater, especially if it was for an extended period. While it's an added expense for the homeowner, it significantly reduces the long-term risk of electrical problems and potential hazards. This is especially true for lower areas of the house.

If Replacement Isn't Immediately Possible (Due to Cost/Logistics)


Thorough Inspection

If replacement isn't immediately feasible, perform a VERY thorough inspection of the Romex. Look for:
Visible corrosion on the conductors (check at outlets, switches, and the panel). Water stains or salt deposits on the cable jacket. Any signs of physical damage. Stiffness or brittleness of the insulation.2.

Megger Testing

Use a megohmmeter (insulation resistance tester) to test the insulation of the Romex. Follow the manufacturer's instructions for proper testing. Any reading below the manufacturer’s recommendations or local codes indicates compromised insulation and requires replacement. If no information is available from the manufacturer, the safe bet is to replace it.3.

Professional Opinion

Consult with a qualified and licensed electrical engineer or master electrician. They can provide a professional assessment of the specific situation and offer recommendations based on their expertise.4.

Documentation

Document everything! Keep detailed records of the inspection, testing results, and any decisions made. This is crucial for liability purposes.5.

Temporary Mitigation

Consider temporary measures like GFCI protection on circuits that
might be affected until full replacement is possible.

What to Replace Definitely



Any wire nuts or other connectors

These will corrode rapidly.


All receptacles and switches

Saltwater contamination can lead to internal corrosion and malfunction.

All circuit breakers in the panel

Even if they look okay, they could have internal corrosion that will lead to failure.


The electrical panel

Saltwater in the panel creates significant corrosion and poses a serious safety risk. A replacement is required.

Communicating with Homeowners and Authorities
Explain the Risks Clearly

Educate homeowners about the potential dangers of saltwater damage to electrical systems. Emphasize the long-term risks of corrosion, electrical faults, and fire hazards.


Document Your Recommendations

Provide written documentation outlining your findings and recommendations. This helps protect you and the homeowner.

Seek Guidance from the Authority Having Jurisdiction (AHJ)

While you're having trouble getting a clear answer, keep pressing the county or local electrical inspectors. Ask them to provide
written guidance or clarification on their expectations for post-flood electrical repairs. Refer to the NEC and the potentially hazardous conditions caused by the storm. A written statement from them will help with compliance and liability.

Important Considerations



Insurance

Encourage homeowners to work with their insurance companies to cover the cost of electrical repairs. Proper documentation and a professional assessment can help with the claims process.

Liability

Make sure your insurance covers work in these situations, and have homeowners sign a waiver acknowledging the risks and agreeing to follow your recommendations.

In summary

While there's no absolute "code requirement" to replace all Romex submerged in saltwater, the
prudent and safest* course of action is to do so, especially if the submersion was prolonged. If replacement isn't immediately possible, a thorough inspection, insulation resistance testing, and professional assessment are essential. Always prioritize safety and err on the side of caution.

Disclaimer:
I am an AI chatbot and cannot provide professional electrical advice. Consult with a qualified and licensed electrician for your specific situation. This information is for guidance only. Flag for review

Previous Question Next Question