Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Marina - High Neutral-Ground Voltage

User: Robert_in_MS, Location: Madison, MS

Asked on: Friday, October 4, 2024 at 12:51 pm EDT
Answered on: Thursday, March 6, 2025 at 3:25 am EST

Question: Hi Folks,I’m in leadership, and have a small boat, at a local marina. We recently had new piers installed and there were issues with the electrical panels and pedestals which first showed up because I was getting a reverse polarity indication (RPL for brevity) in my 1981 vintage trawler. I checked and there was 7.45V between Neutral and Ground when the RPL was on. I then found big problems with the panels and wiring because I do have a good bit of experience with electrical systems and panels, I was a plant engineer at a manufacturing company for years. It was quite a mess, and I was asked to help, so we worked with the same professional electrical engineer to get the drawings revised and same contractor to get everything corrected. I have read thoroughly y’all’s Intro to Article 555 and a detailed article on ABYC Electrical Standard (by Jim? Gilwellbear, Mike is linked in it) which were very helpful in getting everything straightened out. I did search and read thru the forum but could not find enough information to fully help me with my continuing problem.The system is 120V with 30A Shore Power (and 20A GFCI) receptacles fed from a main panel on land, then some 400 ft to a sub-panel in a boathouse, then to a sub-panel on the pier, then to the International Dock Products pedestals. Both before the redo of the panels and wiring, and now, I’ve confirmed that the 30A receptacles were/are wired properly, so my RPL is not actually reversed polarity in the wiring.After everything was corrected and working fine for a number of days, last week my RPL came on again which prevents the AC power from operating in the boat. To troubleshoot, using an adapter, I plugged my shore power cable into an extension cord (I know that’s a nono) into the boathouse and found no RPL. Leaving the boat unplugged to talk to folks about what may have changed. I noticed the big boat next to me had their AC running again, evidently, they had an electrician fix something b/c that boat had been tripping their GFCI breaker (there was not a GFCI breaker before the panel was redone, when I got the 7.45V with their AC running). The next day when I plugged back into the pedestal, miraculously no more problem.I did not have my meter last week so I could not test the voltages. Testing last night, serendipitously, I think I found part of the problem.- With the AC running on the boat next to me I got:N-G 5.63 VL1-N 119.1 VL1-G 113.8 V- BUT when the AC turned OFF on the boat next to me I got:N-G 1.84 VL1-N 120.6 VL1-G 118.8 VI know that the N-G voltage should be zero or certainly less than 1V and I suspect what is tripping my RPL is N-G high voltage (it would be nice to understand why this is). I tried to talk to the EE about this, but he basically blew me off and said 5-7 volts N-G is normal. Well of course it is not, so I need some help determining if there is something amiss with the pier wiring/bonding? and if it that is related to my neighbors AC running causing the N-G voltage to double. I want to get it fixed before somebody potentially gets shocked and have an intelligent conversation with the EE, contractor and boat neighbor. I realize I’m more of an “end user” but given my responsibilities and experience, I hope y’all will indulge in helping me.Link to 4 photos:https://www.dropbox.com/scl/fo/vlmu...ey=rjp8lmsua4yrqkr17aovazmq3&st=p4z6b8hs&dl=0Thanks so much, ROBERT

Robert, you've done a fantastic job documenting and troubleshooting this issue. It's clear you have a good understanding of electrical systems, and you're right to be concerned about the N-G voltage. 5-7 volts is definitely not normal, especially not fluctuating like that. The EE blowing you off is unacceptable, particularly since you were instrumental in getting the system corrected in the first place.Here's a breakdown of what's likely happening, why it's dangerous, and what steps to take

Understanding the Problem: Neutral-Ground Voltage (N-G Voltage)
Ideal Scenario

In a properly wired and bonded system, the Neutral and Ground are connected
only at the main service entrance. This is a critical safety feature. In theory, at any point past the main service entrance, N-G should be very close to 0V.

Why N-G Should Be Near Zero

Neutral carries current back to the source. Ground is a safety conductor, providing a path to trip a breaker if there's a fault (e.g., a short to the metal chassis of an appliance). If Neutral and Ground are at the same potential, then there is no current flowing in the ground wire during normal operation.

Elevated N-G: The Danger

When N-G voltage rises, it means current is flowing in the ground wire. This is problematic for several reasons:


Electrocution Risk

If there's a fault, the elevated N-G voltage makes it much more likely for current to flow through a person who provides a better path to ground than the faulty system.

Corrosion

Stray currents in the grounding system accelerate galvanic corrosion on underwater metal parts of boats.


RPL Trigger

Reverse Polarity Lights are often misnomers. They are actually voltage detectors that detect voltage on the safety ground. If the voltage on the safety ground exceeds ~3VAC, then the indicator is activated, cutting power to the panel.

What's Causing the N-G Voltage?
The most likely culprit is Neutral Current on the Grounding Conductor. This happens when:1. Multiple Neutral-Ground Bonds

If there are additional Neutral-Ground bonds downstream of the main service, current from appliances can take multiple paths back to the source, including through the grounding system.2.

Loose or High-Resistance Neutral Connections

A poor neutral connection forces current to find alternate paths, including the ground wire.3.

Overloaded Neutral

If the neutral conductor is undersized or overloaded, it can develop a voltage drop, forcing some current onto the ground wire.4.

Your neighbor's boat issues

A poorly wired or bonded boat can send neutral current into the dock's grounding system and back to your boat. This is especially true if they have a GFCI tripping problem, which can be caused by ground faults.

Analyzing Your Measurements
The fact that N-G voltage rises significantly when your neighbor's AC is running is very telling. It strongly suggests that your neighbor's boat is contributing to the problem. The fact that you temporarily eliminated the problem by plugging into the boathouse receptacle confirms that the problem is located downstream from there, most likely at the pier sub-panel or in the wiring to your pedestal.

Recommended Steps1. Document Everything

Continue to meticulously document voltage readings under various load conditions (e.g., your boat AC on/off, neighbor's AC on/off, other boats using power). Record the date, time, and conditions. This will be invaluable when discussing the problem with others.2.

Photograph the Wiring

Take detailed photos of the wiring at the pier sub-panel, your pedestal, and your neighbor's pedestal. Look for:
Loose connections, especially on the neutral bus. Any signs of corrosion on connections. Multiple neutral-ground bonds (there should only be ONE at the main service). Undersized wiring.3.

Isolate the Source



Power Down and Check Connections

Disconnect power to the pier sub-panel and carefully inspect all connections. Tighten any loose screws and clean any corroded surfaces.

Check the Grounding Conductor

With the power off, use a multimeter to measure the resistance of the grounding conductor from your pedestal back to the pier sub-panel. It should be very close to zero ohms.


Check for Stray Current

With the power off, use a clamp meter to measure current on the grounding conductor between the pedestal and the pier sub-panel. There should be none.4.

Neighbor's Boat

This is tricky, but you need to address the issue with your neighbor's boat. Tactfully explain the problem and that their electrical issue is impacting other boats in the marina. Do not attempt to troubleshoot their boat yourself. Suggest they have a qualified ABYC-certified marine electrician inspect their wiring.5.

ABYC-Certified Marine Electrician

Insist that the marina hire a qualified ABYC-certified marine electrician to inspect the entire system from the main service entrance to the pedestals. The original EE and contractor clearly missed something. ABYC certification is crucial because it ensures the electrician is knowledgeable about the specific electrical requirements for marinas and boats. Insist they specifically investigate the grounding and bonding system.6.

Ground Fault Circuit Interrupter (GFCI) Protection

Ensure the entire marina electrical system is protected by GFCI breakers, especially at the dock pedestals. 20A GFCI receptacles are good, but they need to be properly protecting the circuit.7.

Written Report and Correction

Demand a written report from the electrician detailing their findings and the corrective actions taken. Verify that the corrections are implemented properly.8.

Boat's Bonding System

Once the dock electrical system is fixed, have your boat's bonding system inspected by a marine electrician to ensure it's properly installed and functioning.

Key Points to Emphasize to the Marina Management



Safety

This is a serious safety issue that poses a risk of electrocution.


Liability

The marina is potentially liable if someone is injured or if there's damage due to electrical problems.

Corrosion

Stray currents accelerate corrosion, leading to expensive repairs on boats.


Reputation

A marina known for electrical problems will lose customers.

Code Compliance

The electrical system
must comply with NEC Article 555 and ABYC standards.

Legal Considerations (Consult an Attorney)

If the marina is unresponsive or refuses to address the issue, consider consulting with an attorney who specializes in maritime law. They can advise you on your legal options, which might include:
Sending a demand letter to the marina. Filing a complaint with the local electrical authority. Pursuing legal action to force the marina to make the necessary repairs.

Important Notes



Never work on electrical systems without proper training and precautions.
Turn off power at the breaker and verify with a multimeter that the circuit is de-energized before touching any wires. Use a qualified marine electrician. This is not a job for a general electrician. Be persistent. Don't let the marina management brush you off. This is a serious issue that needs to be addressed. Continue to document everything. This documentation will be invaluable if you need to take further action.This is a complex issue, but by following these steps, you can help ensure the safety of yourself, your boat, and others in the marina. Good luck! Flag for review

Previous Question Next Question