Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Sjo cord in pvc

User: JJWalecka, Location: New England

Asked on: Friday, October 4, 2024 at 7:21 pm EDT
Answered on: Thursday, March 6, 2025 at 3:27 am EST

Question: Have an injector pump with four float switches and two motors sjo. The plan that was discussed was a hole in the 3.5 foot cover...with Bell end down from LB..up the wall with PVC to injector pump controller.Is it legal to run the sjo cord up the 2" pipe? Should I remove the sho cord sheath as it enters the 2" bell end?Appreciate your insight

Okay, let's break down the scenario and address the legality and best practices for wiring your injector pump.

Understanding the Situation Injector Pump

This likely involves a sump or lift station that pumps liquids from a lower level to a higher level.


Four Float Switches

These detect different water levels in the sump/wet well and trigger the motors.

Two Motors

These are the pumps doing the actual pumping.


SJO Cord

SJO cord is a flexible, oil-resistant cord commonly used for portable appliances, tools, and equipment that may be exposed to moisture, oil, or solvents.

3.5 Foot Cover

This is the lid or covering over the sump/wet well.


Bell End, LB, PVC

This refers to a proposed conduit run using an LB conduit body (a fitting that allows a 90-degree turn in conduit with access for pulling wires) and PVC conduit. The "bell end" usually refers to the flared end of a PVC pipe or fitting designed for solvent welding.

Injector Pump Controller

This is the control panel that receives signals from the float switches and controls the motors.

Legality and Code Considerations (General - Consult Local Codes!)
NEC (National Electrical Code)

Electrical installations must comply with the NEC (or your local equivalent). Local codes often have amendments or variations on the NEC.

Wet Locations

Sump pits and wet wells are inherently wet locations. Wiring methods and equipment must be suitable for wet locations.


Submersible Pumps

Submersible pumps often have specific requirements for their power and control cables.

Conduit Fill

Conduit fill limits restrict the number and size of conductors allowed in a conduit. Overfilling can cause overheating and damage to the conductors.


SJO Cord in Conduit

Generally, NEC 400.8 restricts the use of flexible cords. In particular, 400.8(2) states that flexible cords and cables shall not be used as a substitute for the fixed wiring of a structure. Using SJO cord inside conduit could be a violation. The exception is 400.7(A)(6) which states that flexible cords can be used for connection of utilization equipment to facilitate frequent interchange. Using SJO cord to connect submersible motors and floats to an injector pump control is an acceptable use as long as the cord is protected from damage by conduit.

Answer to your questions
Is it legal to run the SJO cord up the 2" pipe?Potentially Legal (But Not Ideal and Requires Careful Execution)

As the cord would be inside conduit, as the 2" PVC pipe is inside a wet location, the conduit should be watertight.

Remove the Sheath?



NO!
Absolutely do not remove the outer jacket (sheath) of the SJO cord inside the conduit. The outer jacket is part of the cord's insulation system and provides mechanical protection. Removing it would violate the cord's listing and could create a serious safety hazard.

Here's a more robust and code-compliant approach


Seal the Conduit

When transitioning from the wet well to the controller, ensure the conduit is sealed to prevent moisture from entering the controller. Use appropriate sealing fittings at both ends of the conduit run.2.

Consider Liquidtight Flexible Metal Conduit (LFMC)

Instead of rigid PVC, consider using LFMC for the final connection to the pump and floats, especially if there's any vibration or movement. Use appropriate fittings listed for wet locations. This allows for some flexibility and easier maintenance.3.

Use a Junction Box

Install a weatherproof junction box near the top of the wet well, outside of it. This will serve as a transition point:
The SJO cords from the float switches and motors would terminate in this junction box. From the junction box, run THHN/THWN conductors in conduit (PVC or LFMC) to the injector pump controller. THHN/THWN is suitable for wet locations when installed in conduit. Ensure all connections in the junction box are made with appropriate wire connectors suitable for wet locations (e.g., waterproof wire nuts).

Additional Recommendations
Consult a Qualified Electrician

This type of installation is best done by a licensed electrician familiar with local codes and requirements for wet locations and pump control systems.


Grounding

Ensure proper grounding of all equipment and metal conduit (if used).

Overcurrent Protection

Verify that the circuit breaker or fuses are properly sized for the motors and wiring.


Documentation

Keep records of all wiring diagrams and materials used for future reference.

In summary, while running SJO cord in conduit might be technically permissible under specific conditions, a more robust and generally preferred approach involves using a junction box and THHN/THWN conductors in sealed conduit to ensure a safe, code-compliant, and reliable installation.
Always prioritize safety and consult with a qualified electrician. Flag for review

Previous Question Next Question