Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Reducing induced voltage in pump control panel

User: Dubl-P, Location: Saugerties NY

Asked on: Sunday, October 6, 2024 at 9:45 am EDT
Answered on: Thursday, March 6, 2025 at 3:29 am EST

Question: Good day all.I have an audible alarm going off in a septic pump control panel which is sounding off in a flickering/ intermittent way when the float switch powers up the pump.I believe this is due to induced voltage because the float switch and power wiring was run in the same conduit, contrary to the manufacturers instructions as shown on the label on the panel cover.We are in the finishing stages of the project and it would not be great to dig now to run a second conduit.I am looking for the band-aid solution.Can I install a resistor or something like that to manage this trickle of power and prevent the alarm from going off under less than fully powered conditions (when the alarm float switch is actually activated)?Photo at this LINKThanks for your attention!

Okay, I understand the situation. You have an audible alarm intermittently going off when the septic pump activates, likely due to induced voltage in the float switch wiring, caused by running it in the same conduit as the pump power wiring. You're looking for a way to suppress the alarm without re-running the conduit.

First, a VERY IMPORTANT WARNING



Safety First

Working with electrical systems, especially those related to water and pumps, can be extremely dangerous. If you're not completely comfortable and knowledgeable,

hire a qualified electrician
. Improper wiring can lead to electrocution, equipment damage, and fire hazards. This advice is for informational purposes only, and I am not responsible for any outcomes. Code Compliance

Your proposed solution might not be code-compliant. Check local electrical codes before making any modifications. Running power and control wires in the same conduit when not specifically permitted is often a code violation.

Warranty

Modifying the control panel might void the warranty.

Understanding the Problem


The issue is that the pump wiring is inducing a small voltage into the float switch wiring when the pump is running. This small voltage is enough to trigger the sensitive alarm circuit intermittently, even though the float switch isn't actually signaling a high-level condition.

Potential Band-Aid Solutions (with caveats)

Here are a few options, ordered roughly from simplest/least invasive to more complex:1.

Verify Wiring Connections

Double-check all wiring connections, especially at the float switch and the control panel. Ensure they are clean, tight, and properly insulated. Loose or corroded connections can exacerbate the problem.2.

Add a Snubber Circuit (RC Circuit) Across the Float Switch Input

This is a common technique for suppressing voltage spikes and unwanted signals. You'll need to experiment to find the right values, but a typical starting point would be:

Resistor

100k ohm, 1/4 watt resistor.

Capacitor

0.1 uF (100nF), 250V or higher capacitor (film type is preferred).
Connect these components in series, and then connect the resistor-capacitor (RC) network across the terminals of the float switch input to the control panel.



Important

Start with higher resistor values and lower capacitor values. Too much capacitance can interfere with the proper operation of the float switch circuit.

How it works

The capacitor absorbs the induced voltage spikes, and the resistor limits the current flow into the capacitor.3.

Alarm Circuit Adjustment

If possible, there may be a sensitivity adjustment on the alarm circuit within the control panel. See if there's a potentiometer ("pot") or dip switches that control the alarm's trigger threshold.

CAUTION

Adjusting this improperly can make the alarm non-functional.
Exercise extreme caution and document the original setting before making any changes. Adjust the sensitivity only slightly until the intermittent alarm stops.4.

Add a Relay with a Hysteresis Circuit
This involves wiring a relay in between the float switch and the control panel. The relay is activated by the float switch.

Hysteresis can be added to the relay coil circuit (using resistors) so that it requires a higher voltage to initially activate the relay, but a lower voltage to keep it activated. This can prevent the relay from rapidly switching on and off due to the induced voltage.

Why a Simple Resistor Alone Might Not WorkA simple resistor across the float switch input would reduce the impedance of the circuit, potentially lowering the induced voltage seen by the alarm. However, it could also: Significantly reduce the voltage seen by the control panel when the float switch is activated, preventing the alarm from triggering when it should. Draw a continuous current, potentially damaging the float switch or the control panel.

Why Running Separate Conduits is the Preferred Solution

Reduced Interference

Separating power and control wiring minimizes inductive coupling and the associated noise problems.


Code Compliance

Often required by electrical codes for safety.

Reliability

Provides the most reliable and predictable operation of the system.


Safety

Minimizes the risk of unintended consequences.

Recommendation


Start with the simplest steps

Double-check wiring connections first.2.

Try the snubber circuit

This is a relatively common and often effective approach. Start with the suggested values and adjust as needed.3.

Consider professional help

If the above steps don't work, or if you're not comfortable working with electrical components, contact a qualified electrician. They can diagnose the problem more accurately and provide a safe and code-compliant solution.4.

As a last resort only

If you can adjust alarm sensitivity you can try that, very carefully documenting the original settings.

Disclaimer:This information is for general guidance only. I am not a licensed electrician, and this information should not be considered a substitute for professional advice. Always prioritize safety and consult with qualified professionals when working with electrical systems. Flag for review

Previous Question Next Question