Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Electric Heater Equipment Circuit

User: faresos, Location: Connecticut

Asked on: Tuesday, October 8, 2024 at 9:42 am EDT
Answered on: Thursday, March 6, 2025 at 3:35 am EST

Question: Question, NEC 424.4 (A) states "Branch circuits supplying two or more outlets for fixed electric space-heating equipment shall be rated not over 30 amperes.", does this mean I can power two heaters from 30A circuit without the need to provide a fused disconnect (using tap rule) at each unit?Thank you!

You're interpreting NEC 424.4(A) correctly in that it potentially allows you to power two or more fixed electric space heaters from a single 30-ampere branch circuit. However, there are several conditions and considerations that need to be met before you can do this safely and in compliance with the NEC. You cannot skip the fused disconnect (or other compliant disconnecting means) by using a tap rule in this scenario.Here's a breakdown of the requirements and why you need to be careful: Heater Listing and Markings

The most important factor is the listed and marked current draw (in amps or watts) of each individual heater. You
must ensure that the total calculated load of all heaters connected to the 30-amp circuit does not exceed 80% of the circuit's rating (24 amps for a 30-amp circuit). This includes any auxiliary equipment like fans or blowers integrated into the heaters.

Nameplate Data is Key

The nameplate on each heater will have critical information, including voltage, amperage (or wattage), and any minimum circuit ampacity requirements. Use this information to perform your load calculations.

Disconnecting Means

Each heater

must
have a readily accessible disconnecting means. This doesn't necessarily have to be a fused disconnect, but it must be capable of disconnecting all ungrounded conductors simultaneously. A circuit breaker lockable in the "off" position at the panel may be used in some cases, but a local disconnect is almost always preferable for service and safety. The location must comply with 424.19. Code Articles Affecting the Install



424.19(A): Unit Switch as Disconnecting Means

The provision allowing the unit switch to serve as the disconnecting means requires two conditions: The unit must be installed within sight of the panelboard where the branch circuit originates. The switch must disconnect all ungrounded conductors of the circuit. If either of these conditions cannot be met, another method of disconnect compliant with 424.19(B) must be installed.

424.19(B): Manually Operable Switch or Circuit Breaker as Disconnecting Means

A readily accessible disconnecting means, such as a manually operable switch or circuit breaker, must be located within sight from the unit, which disconnects all ungrounded conductors of the circuit.

Tap Rules Don't Apply in This Case

The tap rules are designed for specific scenarios, and they don't generally apply in this situation where you're connecting multiple fixed appliances (electric space heaters) to a branch circuit. The need for individual disconnecting means outweighs the limited applicability of tap rules. The purpose of a tap rule is to allow you to run a shorter length of smaller gauge wire to a single device while still meeting overcurrent protection requirements. It's not meant for powering multiple fixed heating appliances from a single tap without individual protection and disconnection.

Why the Fused Disconnect (or suitable alternative) is Important



Safety

If a fault occurs in one heater, a fused disconnect (or the correct circuit breaker) will isolate that fault and prevent it from affecting the other heater and potentially causing a fire or other hazard.

Maintenance

A disconnecting means allows you to safely service or replace a heater without de-energizing the entire branch circuit.


Overcurrent Protection

It provides local overcurrent protection to the appliance, preventing the conductors that supply the heaters from being damaged by a fault within the appliance.

In Summary

While NEC 424.4(A) allows you to put multiple heaters on a single 30-amp circuit, it requires careful planning and adherence to all applicable code rules. You need to verify the load requirements of each heater, calculate the total load on the circuit, and, crucially, provide a disconnecting means for each individual heater. Do not try to use tap rules to avoid providing proper overcurrent protection and disconnecting means for each unit.

Recommendation:


Consult with a licensed electrician to ensure your installation complies with all applicable NEC requirements and local codes. Electrical installations involving heating equipment should be done by qualified professionals to ensure safety. Flag for review

Previous Question Next Question