Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: What 508A UL is saying about using a control panel as a raceway or a pull box?

User: Alex Foster Sr., Location: Toronto, Canada

Asked on: Tuesday, October 8, 2024 at 1:53 pm EDT
Answered on: Thursday, March 6, 2025 at 3:36 am EST

Question: My co-designer wants to use control panel as a raceway or a pull box an is claiming that UL508A doesn't restrict that.Any comments?Alex

Your co-designer is likely wrong, but it's a nuanced issue. Here's a breakdown of why and what to consider

Why Using a Control Panel as a Raceway/Pull Box is Generally Discouraged and Often Prohibited by UL 508A:
Dedicated Function

UL 508A panels are designed and certified to house control equipment. Using them as a raceway fundamentally changes their intended use and compromises their safety rating.


Overcrowding and Heat Dissipation

Adding unrelated wiring fills the panel, potentially interfering with internal wiring, reducing airflow, and hindering heat dissipation. Control panels are designed for specific heat loads. Introducing more wiring and potential heat sources can overload the system.

Accessibility and Maintenance

Excess wiring makes it difficult to access control components for maintenance and troubleshooting. It creates a cluttered and potentially hazardous environment.


Insulation Damage

Pulling wires through tight spaces can damage insulation, leading to shorts and ground faults.

Clearance Requirements

UL 508A mandates specific clearance requirements between components and between wiring and components. Adding "pass-through" wiring likely violates these clearances.


Potential for Induced Voltage

Running power conductors alongside sensitive control wiring can induce voltage, causing malfunctions.

Listing Concerns

The UL508A listing applies to the panel as it was
originally designed and tested. Altering its function significantly raises questions about the validity of the listing.

Arguments Your Co-Designer Might Make and Why They're Often Insufficient



"UL 508A doesn't explicitly prohibit it"

While the standard might not have a single, easily quotable sentence saying "you cannot use a control panel as a raceway," it's prohibited implicitly through numerous requirements and principles. The entire premise of UL 508A is about safe control panel design for its intended function.

"If the fill is within the NEC limits, it's OK"

NEC fill calculations for raceways don't automatically translate to control panels. Panel internal wiring and component arrangement are different. Also, NEC wire fill relates to heat and physical damage concerns, but UL508A has concerns about clearances and access to components.


"We're just running a few wires"

The amount of wiring doesn't necessarily negate the risk. Even a few improperly run wires can compromise safety and accessibility.

When it Might Potentially be Acceptable (Very Rare and Requires Justification)



Designed from the Outset

IF the panel was specifically designed and UL listed to accommodate pass-through wiring, with appropriate barriers, clearances, and labeling, and the documentation explicitly allows it, then it might be permissible. This is extremely rare.

Exception for Specific Control-Related Wiring

Minor routing of control wires directly related to the panel's control function within the panel itself is acceptable and intended. We're talking about the panel's own wiring, not wires from other equipment using the panel as a pass-through.

Consult UL

The
only definitive answer is to consult with UL directly. Provide them with detailed drawings of the proposed wiring, component arrangement, and panel specifications. They will determine if the modifications are acceptable and if the listing remains valid. Get this in writing.

What You Should Do

1.

Review UL 508A Thoroughly

Focus on sections related to internal wiring, clearances, heat dissipation, and intended use.2.

Document Your Concerns

Clearly explain to your co-designer why using the panel as a raceway is problematic. Use the points above.3.

Suggest Alternatives

Propose alternative wiring solutions, such as:


Separate raceways

Run dedicated conduits or wireways for the wiring that needs to pass through the area.

Junction boxes

Use appropriately sized junction boxes or pull boxes at strategic locations.


Larger Enclosure

Select a larger control panel that can house both the control components and related wiring. But even this may not be allowed, depending on the amount of "pass-through" wiring.4.

Contact UL (Important!)

Contact UL directly to get their opinion on the proposed use of the panel. This is the most authoritative answer you can get. Provide them with detailed plans and documentation.5.

Document Everything

Keep records of all communication, discussions, and decisions. This is crucial for liability and traceability.

In conclusion, using a control panel as a raceway or pull box is generally a bad idea and likely violates UL 508A. It compromises the panel's safety rating, increases the risk of failures, and makes maintenance difficult. Always prioritize safety and compliance with the standard. Contacting UL directly is the best way to get a definitive answer for your specific situation.
Flag for review

Previous Question Next Question