Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 70 year old recess light

User: sparkync, Location: North Carolina

Asked on: Tuesday, October 8, 2024 at 2:34 pm EDT
Answered on: Thursday, March 6, 2025 at 3:37 am EST

Question: I have a customer who needs the tubes changed in an old recess light fixtures. It is a 1x4 wirh a glass lens. I can't figure how to get into it, without taking rhe whole outside of the frame down. If I do that it will take two men, since it's going to be heavy. I'm trying to send a picture of it but haven't figured out how yet. It says "file is to large". It has a small piece of metal going horizontal half way of the length. It has a "thumb screw" in it, which I tried to unscrew, but it stopped about 3/4 inch out. I was afraid to "force" it anymore just in case it wouldn't go back in. With this crude information has anyone seen anything like it? Homeowners says it's 70 years old.I know, without a picture, you would have to be psychic., thanks anyway.

Okay, based on your description, it sounds like a very old fluorescent fixture. Here's a breakdown of likely possibilities and how to approach it, given the limitations

Understanding the Challenges
Age

70 years old means the fixture is likely built with different design philosophies and materials than modern fixtures. Expect things to be stiff, possibly rusted, and delicate.


Weight

1x4 fluorescent fixtures, especially older ones with heavy ballasts and housings, are surprisingly heavy. Your concern about needing two people to remove the entire frame is valid.

Thumb Screw

This is the key. You are likely right about the purpose.


Lens

The glass lens adds more weight and fragility.

Possible Entry Methods (Based on Description)
1. The Thumb Screw & Center Support

This is the most likely point of entry.

Reasoning

The thumb screw likely secures a center support or retaining bar that holds the lens or a lens frame in place.


Troubleshooting



Don't Force

You were right to stop when it wouldn't come out easily. Forcing it could damage the threads or the mechanism.


Lubricant

Apply a small amount of penetrating oil (like WD-40 or PB Blaster) to the thumb screw and the area where it threads into the support. Let it sit for 15-30 minutes. Try unscrewing it again.

Wiggle & Pull

While unscrewing, try gently wiggling the center support or gently pulling downwards on it (if possible without stressing the lens). It might be catching on something.


Look for a Catch

Shine a light around the thumb screw and the center support. Look for any other small screws, clips, or catches that might be holding the support in place.

Internal Stop

It's possible the thumb screw is designed to only unscrew a certain amount. The center support may then slide sideways or pivot. Look for any play or movement in the support after unscrewing the thumb screw as much as you can.


Once the Center Support is Removed

The lens or lens frame should either: Slide out to one side. Drop down (be extremely careful!). Have another set of fasteners (clips, screws) holding it in place.2.

Lens Frame Removal

If the center support doesn't release the lens directly, it might release a lens frame.


Look for retaining clips or screws

Examine the edges of the lens frame carefully. There may be clips that need to be squeezed or screws that need to be loosened.

Pry carefully

If there are no visible fasteners, the frame might be friction-fit.
Very carefully use a thin, dull putty knife or flathead screwdriver to gently pry around the edges of the frame. Be extremely cautious not to scratch or break the lens.3.

Full Frame Removal (Last Resort)

Only do this if you absolutely cannot access the tubes any other way.


Two People

You were right; this is a two-person job for safety.

Power Off

Turn off the power to the circuit at the breaker box.
Verify it's off with a non-contact voltage tester!



Support the Fixture

Before loosening the mounting screws, have your helper support the fixture from below.

Loosen Screws

Loosen and remove the screws holding the fixture to the ceiling.


Lower Carefully

Slowly and carefully lower the fixture.

Disconnect Wires

Disconnect the wires inside the junction box, noting their connections.


Once Down

You should have full access to the interior of the fixture to replace the tubes.

Important Safety Considerations



Power Off

Always turn off the power at the breaker box before working on electrical fixtures.

Non-Contact Voltage Tester

Use one to confirm the power is off.

Eye Protection

Wear safety glasses to protect your eyes from dust, debris, and potential glass shards.


Gloves

Wear work gloves to protect your hands.

Ladder Safety

Use a stable ladder and follow ladder safety guidelines.


Asbestos

While unlikely, given the age, there's a very slight chance of asbestos-containing materials. If you encounter any suspicious materials that look like insulation, stop work and have it tested.

Before Replacing the Tubes



Ballast

Consider replacing the ballast while you have access. Old ballasts can be inefficient, noisy, and prone to failure. If the ballast is very old (tar-like substance) it may contain PCBs. Contact your local disposal agency for proper procedures.


Wiring

Inspect the wiring for damage (cracks, fraying, etc.). Replace any damaged wiring.

Clean

Clean the inside of the fixture and the lens before reassembling.

Why Your Picture Might Be Too Large



Resolution

Most phones take very high-resolution photos these days.

Solutions



Email

Email the picture to yourself, then save it. Email services often automatically compress images.

Image Editing

Use a photo editor (even the one built into your phone) to reduce the resolution of the image. A width of 1000-1200 pixels is usually sufficient.


Online Resizer: There are many free online image resizing tools (just search for "image resizer").Good luck! Be patient, be gentle, and take your time. If you're not comfortable working with electrical fixtures, it's always best to call a licensed electrician. Flag for review

Previous Question Next Question