Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Testing ground for voltage

User: The electron man, Location: Nyc

Asked on: Tuesday, October 8, 2024 at 8:44 pm EDT
Answered on: Thursday, March 6, 2025 at 3:38 am EST

Question: Let's say I working on some electrical and I'm testing for voltageFromGround to black I should get 120vGround to red I should get 120vGround to neutral I should get 0vSince ground and neutral are at the same potentialBut there are times the ground can be energized because there is a problem in the systemHow would I test the ground to make sure its not energized ??

You're right, a properly functioning ground wire should be at or very near 0V relative to neutral. However, an energized ground is a dangerous situation! Here's how to test the ground to make sure it's not energized, and what to do if it is

Safety First! Assume the Ground is Energized Until Proven Otherwise.
Always work with power OFF if possible! This is the best way to guarantee your safety. If you absolutely must test with power on, use extreme caution and wear proper personal protective equipment (PPE), including insulated gloves and eye protection. Use a properly rated and functioning multimeter. Make sure your meter is designed for the voltage you're testing (120V or higher in this case) and that it's in good working order. Check it on a known voltage source before using it to test for problems. Do NOT touch any bare wires or connections. This should be obvious, but it's worth repeating.

Testing Procedure1. Voltage Test: Ground to Neutral
Set your multimeter to AC Voltage (VAC) mode. Make sure the range is high enough for 120V. Carefully place one probe of your meter on the ground conductor (the bare wire or green insulated wire). Carefully place the other probe of your meter on the neutral conductor (usually a white wire). Reading Interpretation



0V (or very close to 0V)

This is what you expect to see in a properly working system. The ground is not energized. A very small reading (a volt or two) might be acceptable depending on circuit length and load, but anything higher warrants further investigation.

Any Voltage Significantly Above 0V

This indicates that the ground wire is energized. This is a dangerous fault.2.

Voltage Test: Ground to Known Good Ground (if available)
This is an extra check you can do if you have access to a known, reliable grounding point that is completely separate from the electrical circuit you're testing. A metal cold water pipe that runs directly into the ground can sometimes be used, but confirm that it actually is grounded first! Repeat the voltage test as above, placing one probe on the ground conductor you're testing and the other on the known good ground. Reading Interpretation



0V (or very close to 0V)

Confirms that the ground is good.


Any Significant Voltage

Confirms that the ground is energized.3.

Continuity Test (with power OFF ONLY!)
Turn off the circuit breaker supplying power to the circuit you're testing! Double-check with a voltage tester to confirm the circuit is de-energized. Set your multimeter to continuity test mode (usually indicated by a sound symbol). Place one probe on the ground conductor and the other on a known good ground (like a metal cold water pipe as described above). Reading Interpretation



Continuity (meter beeps or reads close to 0 ohms)

The ground conductor is properly connected to ground.


No Continuity (meter does not beep or reads very high resistance)

The ground conductor is not properly connected to the grounding system. This is a problem!

What to Do If the Ground is Energized
Immediately turn off the circuit breaker supplying power to the affected circuit. Do NOT touch anything connected to the circuit. Call a qualified electrician immediately! An energized ground indicates a serious problem that needs professional diagnosis and repair. Do not attempt to fix it yourself unless you are a qualified electrician.

Possible Causes of an Energized Ground
Faulty Appliance

A short circuit inside an appliance can cause current to flow through the grounding wire.

Damaged Wiring

Damaged insulation on a hot (black) or neutral (white) wire can allow it to come into contact with the metal enclosure of an appliance or the ground wire.


Loose Connections

Loose connections in the grounding system can increase resistance, leading to voltage on the ground wire.

Improper Wiring

Incorrect wiring, such as reversed polarity or a missing ground connection, can cause an energized ground.


Shared Neutral

Improperly sharing a neutral wire between multiple circuits (especially if the circuits are on opposite phases) can overload the neutral and cause current to flow through the ground.

Important Considerations



Ground Fault Circuit Interrupters (GFCIs)

GFCIs are designed to detect small imbalances in current flow between the hot and neutral wires. If a GFCI detects current flowing through the ground path, it will trip the circuit breaker, preventing electrical shock. They are not a substitute for a properly wired ground, but they provide an important additional layer of safety. Make sure your circuits in wet or damp locations (bathrooms, kitchens, outdoors) are GFCI protected.


Arc Fault Circuit Interrupters (AFCIs)

AFCIs are designed to detect arc faults, which are dangerous electrical discharges that can cause fires. They are now required in many new construction projects.

In summary, always prioritize safety when working with electricity. If you are unsure about anything, consult a qualified electrician.
Flag for review

Previous Question Next Question