Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Hard Time Understanding 110.14 C

User: payneeco, Location: 4691 Northwest Parkway Hilliard Ohio 43026

Asked on: Wednesday, October 9, 2024 at 11:52 am EDT
Answered on: Thursday, March 6, 2025 at 3:40 am EST

Question: Using Mike Holt Understanding the NEC Volume 1 to Study for Electrical Exam. Here is the question: What is the minimum size secondary conductor required for a single phase 1.5 KVA 480 to 120 V transformer that is protected with a 5A fuse on the primary. I understand the solution until it gets to step 4 and they use 60 degrees c to size wire on table 310.16. This gets me a lot because I don't fully understand 110.14 (C)(1) ....which unfortunately is referenced a lot in a broad range of questions. Can someone help me understand when to use 60 C versus 75 C versus 90 C. I'm looking for ways to master just this one small thing. I'm thinking it would go a long way on the exam if I just fully understood this one thing.

Okay, let's break down NEC 110.14(C)(1) and how it applies to conductor sizing, specifically with transformer examples like the one you're studying. This is a crucial section, so understanding it will definitely boost your exam performance.

Understanding 110.14(C)(1): Termination Temperature Limitations

This section deals with the temperature rating of the terminals to which you are connecting your conductors, and how that impacts the ampacity (current-carrying capacity) you can use from Table 310.16. Think of it this way: the weakest link determines the overall strength of the system.The rule says (paraphrased): Conductors with ampacities determined by 310.16 shall be selected and installed so that the temperature rating of the termination shall not exceed the temperature rating of the conductor. In no case shall conductors be loaded such that the conductor temperature exceeds that for which the wire is rated.Here's the breakdown: Terminals

These are the points where you connect the wire to devices like circuit breakers, transformers, switches, receptacles, etc. Every termination has a temperature rating listed on the device. (60C, 75C, 90C)


Conductor

The wires themselves are rated for a maximum operating temperature as well. (60C, 75C, 90C).The NEC is concerned about the heat generated by the current flowing through the conductor. If the terminals can't handle that heat, you need to adjust the ampacity you use.

The Rule's Impact on Wire Sizing

The NEC is essentially saying, "You can't push more current through a wire than the weakest link in your system can handle." This is why you might have to use the 60°C or 75°C column in Table 310.16, even if your wire is rated for 90°C.

The General Rule


Identify the Temperature Ratings

Determine the temperature rating of both the

conductor insulation
(e.g., THHN is typically rated 90°C) and the terminals at each end of the conductor (e.g., a circuit breaker might be marked 75°C).2. Apply the Rule

You must use the lowest of these two temperature ratings when selecting the ampacity from Table 310.16, unless you have specific equipment listings that allow otherwise (more on this below).

Common Scenarios and Temperature Ratings



100 Amperes or Less, Terminations Rated 60°C

If your circuit is rated 100 amps or less AND your equipment terminations are only rated for 60°C, you must use the 60°C column in Table 310.16 to determine the ampacity of your wire. You can use a 90C wire, but it has to be sized as if it's a 60C wire.

Over 100 Amperes, Terminations Rated 75°C

If your circuit is rated
over 100 amps OR your equipment terminations are rated for 75°C, you must use the 75°C column in Table 310.16. Again, you can use a 90C wire, but it has to be sized as if it's a 75C wire.

Exceptions and Key Considerations



Equipment Listed and Marked

This is the critical exception. If the equipment is specifically listed and marked to allow for higher temperature terminations (e.g., it says "Suitable for 90°C terminations"), then you can use the 90°C ampacity.

Read the equipment nameplate!
Conductor Ampacity vs. Overcurrent Protection

Remember that the ampacity of your conductor must be sufficient to carry the load, but it also must be protected by an overcurrent device (circuit breaker or fuse) sized appropriately. You can't simply use a higher ampacity wire to get around overcurrent protection rules.

Back to Your Transformer Example

Let's revisit why Mike Holt's solution uses 60°C in your transformer problem.1.

Calculate Secondary Current

You correctly calculated the secondary current to be 12.5 amps.
2.


NEC 240.4(D)

The solution probably references this article. This section requires that if a conductor does not correspond to the standard fuse and breaker sizes, then you go up to the next size. For example, using 14 AWG the maximum fuse you could protect this circuit with is 15 amps. However, 240.4(D) does not apply if the circuit supplies a transformer, so this section does not apply.
3.


110.14(C)(1) Application

Now, here's where 110.14(C)(1) comes in. Unless you know that the terminals on the transformer
and the load-side breaker/fuse panel are specifically listed and marked for 75°C or 90°C terminations, you must assume the default 60°C rating for circuits 100 amps and under.4.

Table 310.16, 60°C Column

Therefore, you must look at the 60°C column in Table 310.16 to find a conductor with an ampacity of at least 12.5 amps. A 14 AWG copper conductor is the smallest conductor that can safely carry the load.

In Summary: How to Master This
1. Memorize the General Rule

Termination temperature rating governs the ampacity you can use from Table 310.16. Use the
lowest* of the conductor insulation rating and the terminal temperature rating.2.

Understand the 100A Threshold

Know the 60°C default rule for 100A and under circuits and the 75°C default rule for over 100A circuits.3.

Focus on the Exception

The most important part is the "unless listed and marked" exception. Always check the equipment nameplate for temperature ratings.4.

Practice:
Work through many examples like your transformer problem. Force yourself to consciously consider 110.14(C)(1) in each case.By consistently applying these steps, you'll develop a strong understanding of 110.14(C)(1) and be well-prepared to tackle similar questions on your electrical exam. Good luck! Flag for review

Previous Question Next Question