Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Technical side of 0-10V dimming, and remote switching.

User: fastline, Location: midwest usa

Asked on: Wednesday, October 9, 2024 at 4:01 pm EDT
Answered on: Thursday, March 6, 2025 at 3:42 am EST

Question: We are redesigning a facility for manufacturing. The design is using UFO LED lights. I am highly recommending dimming, as most fixtures have it. However, I am realizing based on supplier talks that I may not fully understand the engineering side of dimming in the drivers because these dimmers are wattage or current limited. It was always my understanding that the 0-10VAC (or is it DC?) was only a signal voltage. Apparently they consume or transfer quite a bit of power. I asked them if the dimmer is a simple rheostat but they didn't know what that was.Understanding them will be vital to me designing the circuit diagram.As well, as I lay this out, I'd like to see if there are any products for commercial use to move lighting switching to more remote locations? As an example, the customer may desire to have all light switching in a single location, in a building that is over 300ft long, creating long, pointless runs of power wire. I have considered running contactors to handle the loads, but there has to be a better way.

You're right, understanding LED dimming and remote switching solutions is crucial for a modern manufacturing facility design. Let's break down the complexities

Understanding 0-10V Dimming for LED UFO Lights:

1. Signal vs. Power

You're on the right track with your initial understanding. 0-10V dimming is a low-voltage control signal, not a high-power control method. The power for the LED comes directly from the driver's power supply. The 0-10V signal simply tells the driver how much power to deliver to the LED.2.

0-10V: DC Voltage

Yes, 0-10V dimming uses a DC voltage signal.3.

How it Works (Simplified)



10V = 100% Brightness

When the 0-10V signal is at 10V, the LED driver delivers its full rated current (and thus, full brightness) to the LED.


0V = Lowest Brightness (Sometimes Off)

When the 0-10V signal is at 0V, the LED driver delivers the minimum current (which might be a very low level of light, or even completely off, depending on the driver's design). Some drivers have a "dim-to-off" feature, while others will only dim to a low level (e.g., 10%).

Intermediate Voltages

Voltages between 0V and 10V correspond to intermediate brightness levels. For example, 5V
should (in theory) give you approximately 50% brightness, but the dimming curve is often not perfectly linear.4.

The Dimmer's Role

The 0-10V dimmer acts as a
signal source or a signal controller, not a power regulator. It provides a DC voltage that the driver interprets. Think of it like the volume knob on a stereo amplifier. You're not controlling the power to the speakers directly; you're just telling the amplifier how much power to send.5.

Why "Wattage or Current Limited"?
This is where things get nuanced. The "wattage or current limited" refers to the dimmer controller's ability to supply the 0-10V signal and maintain a stable voltage across the dimming input of the LED drivers. Each LED driver places a small "load" on the 0-10V dimming circuit (it "sinks" a tiny amount of current). If you have too many LED drivers connected to a single dimmer, the dimmer might not be able to supply enough current to maintain the correct 0-10V signal. This can lead to inconsistent dimming, flickering, or the lights not dimming properly. The dimmer controller's specification sheet will tell you the maximum number of drivers it can control. This is usually expressed as a maximum "sink current" or "number of compatible drivers."6. Rheostat Analogy

A rheostat (a variable resistor) could be used to generate a 0-10V signal, but it's not the most common or efficient approach. Modern 0-10V dimmers are typically electronic devices that provide a more precise and stable DC voltage output. The supplier likely didn't know what a rheostat was in the context of controlling the 0-10V signal because that's an older, less common method. They are probably used to modern electronic dimming controllers.

In Summary (for your circuit diagram)

You need a low-voltage (usually 12V or 24V DC) power supply to power the 0-10V dimmer. The 0-10V dimmer provides a DC voltage signal to the 0-10V input on the LED driver. The LED driver receives line voltage (120V, 277V, etc.) and converts it to the DC voltage needed by the LED.

Crucially

Make sure the dimmer is compatible with the LED drivers you're using. Check the dimmer's specifications for:


Output voltage range

Is it truly 0-10V DC?

Maximum sink current (or number of drivers supported)

This is the most important.


Compatibility with the driver's dimming curve

Some drivers expect a linear 0-10V curve; others might use a logarithmic curve.

Wiring

0-10V dimming often uses low-voltage wiring (like 18 AWG or 22 AWG). It's separate from the power wiring.

Addressing Remote Lighting Switching

You're right; long runs of power wire just for switching are inefficient and costly. Here are some better solutions for remote switching:1.

Wireless Lighting Control Systems (Most Flexible and Scalable)



How they work

These systems use wireless communication (Zigbee, Bluetooth Mesh, Wi-Fi, EnOcean, etc.) to control lights.

Components



Wireless Switches/Keypads

These are placed in the desired switching locations. They don't need to be wired directly to the lights.

Wireless Lighting Controllers/Modules

These are installed at the light fixtures (or in a central location). They receive the wireless signals and switch the lights on/off or control dimming. These modules are often built
into the LED drivers.

Gateway/Hub (Sometimes Required)

A central hub might be needed to manage the network and provide connectivity to a smartphone app or building management system (BMS).

Benefits



Reduced Wiring

Significantly reduces or eliminates the need for long wire runs for switching.

Flexibility

Easy to reconfigure lighting zones and add new switches/lights.


Advanced Features

Often include scheduling, scene control, occupancy sensing, daylight harvesting, and energy monitoring.

Examples



Philips Hue

(More residential-focused, but can be used in small commercial settings)

Caseta by Lutron

(Good for retrofit projects)


Enlighted (Siemens)

(Advanced, commercial-grade system)

Synapse Wireless

(Industrial-focused)


Wattstopper (Legrand)

(Commercial lighting controls)

Considerations



Cost

Can be more expensive upfront than traditional wiring, but the long-term benefits (reduced wiring, energy savings, flexibility) can often justify the investment.

Reliability

Choose a system with a robust wireless protocol (e.g., Zigbee, Bluetooth Mesh) and good range.


Security

Ensure the system has adequate security measures to prevent unauthorized access.

Interoperability

If you're integrating with a BMS, make sure the system is compatible.2.

Low-Voltage Lighting Control Wiring with Addressable Systems (DALI, DMX)



How they work

Instead of running line voltage to switches, you run low-voltage data wires (often just two wires) to each lighting fixture. Each fixture has a unique address. The central controller sends commands to individual fixtures or groups of fixtures.

DALI (Digital Addressable Lighting Interface)

A common standard specifically for lighting control.


DMX (Digital Multiplex)

More common in stage lighting, but can be used for architectural lighting.

Benefits



Centralized Control

All lighting is controlled from a central location.

Individual Fixture Control

You can control each fixture independently (brightness, color, on/off).


Flexibility

Easy to create lighting scenes and adjust lighting levels.

Considerations



More Complex Wiring

Requires running data wires to each fixture.

Higher Initial Cost

DALI/DMX controllers and drivers are more expensive than standard drivers.


Programming

Requires some programming knowledge to set up the system.3.

Power Line Communication (PLC) (Less Common)



How it works

Sends control signals over the existing power lines. No new wiring is needed.


Benefits



No New Wiring

The biggest advantage.


Considerations



Reliability

Can be affected by noise on the power lines.


Limited Functionality

Typically only supports on/off switching, not dimming.

Not Widely Used

Not as popular as wireless or DALI systems.4.

Contactors with Centralized Control (A Simpler Approach)



How it Works

You have a central panel with low-voltage switches. These switches control low-voltage relays (contactors) located closer to the lighting circuits. The contactors switch the high-voltage power to the lights.

Benefits



Simpler than Wireless or DALI

Easier to understand and troubleshoot.


Reliable

Contactors are robust and reliable devices.

Considerations



Still Requires Some Wiring

You need to run low-voltage control wiring from the central panel to the contactors.

Limited Functionality

Typically only supports on/off switching.


Not as Flexible

More difficult to reconfigure lighting zones.

Recommendations for Your Manufacturing Facility


For a 300ft+ Long Building, strongly consider wireless lighting control.
The flexibility, reduced wiring costs, and advanced features will likely outweigh the upfront cost. Research Zigbee and Bluetooth Mesh based systems that are designed for commercial environments.2. If you need granular control of each fixture (e.g., for specific tasks), consider DALI.3. If you just need simple on/off control and want a very reliable (but less flexible) solution, contactors with centralized control could be an option.Steps for Implementation


Define Your Requirements

What level of control do you need (on/off, dimming, color control)? Do you need zoning capabilities? Do you need to integrate with a BMS? What's your budget?2.

Research Different Systems

Talk to lighting control manufacturers and distributors. Get quotes for different systems.3.

Pilot Project

Install a small-scale pilot project in one area of the facility to test the chosen system.4.

Full-Scale Implementation:
Roll out the system throughout the facility.By carefully considering your needs and the available technologies, you can create a lighting system that is efficient, flexible, and meets the specific requirements of your manufacturing facility. Remember to prioritize long-term cost savings and future adaptability when making your decisions. Flag for review

Previous Question Next Question