Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 120/240v single phase subpanel fed from 208y/120v three phase main breaker panel

User: chris k baker, Location: United States

Asked on: Thursday, October 10, 2024 at 12:35 pm EDT
Answered on: Thursday, March 6, 2025 at 3:44 am EST

Question: I'm looking for suggestions on the best way to run a 60 amp 120/240 single phase subpanel from a 208y/120 three phase panel. Is a buck boost transformer needed, etc. Thanks for any help!

Okay, here's a breakdown of how to run a 60A 120/240V single-phase subpanel from a 208Y/120V three-phase panel, addressing whether you need a buck-boost transformer and other important considerations.

The Problem: Voltage Mismatch

The key issue is the voltage difference. You have a: Source Panel

208Y/120V three-phase. This means that
Line-to-Line voltage is 208V, and Line-to-Neutral voltage is 120V.

Target Subpanel

120/240V single-phase. This requires 240V Line-to-Line.

The Answer: Yes, you need a Voltage Correction


Because your source voltage is 208 volt line to line, and you need 240 volt line to line. You're short 32 volts (240 - 208 = 32). A buck boost transformer can be used to correct for this, by "boosting" the voltage from 208 to 240.

Option 1: Buck-Boost Transformer (Recommended)

This is generally the
best and most reliable solution, especially for a 60A load. How it works

A buck-boost transformer is a small, specialized transformer designed to add or subtract a small amount of voltage to the input to give you the proper output. In your case it's wired to boost the voltage. They are relatively efficient and reliable.

Sizing

The transformer needs to be sized to handle the voltage boost
and the current. The voltage boost is 32 volts. To calculate the VA required: 32V 60A = 1920 VA. Important Considerations:



Nameplate Ratings

The transformer must be rated for continuous duty at the required current and voltage. Don't undersize it. It needs to handle 60 amps, not just for short periods.

Wiring Diagram

Carefully follow the manufacturer's wiring diagram for the
boost configuration.

Location

Mount the transformer in a dry, ventilated location near the source panel or the subpanel (whichever is more convenient for wiring). Consider its weight and mounting requirements.

Safety

Turn off power before working on any electrical equipment. Have a qualified electrician do the final connections and inspection.


Pros

Provides a true 240V, which is ideal for appliances designed for that voltage. Relatively efficient. Reliable.

Cons

Cost (initial purchase and installation). Space required for the transformer.

Wiring and Installation (General Guidelines - Consult a Qualified Electrician)1.

Permits

Check with your local building department to determine if permits are required for this type of electrical work.2.

Disconnect

Turn off the main breaker at the source panel before starting any wiring. Double-check with a multimeter to ensure the power is off.3.

Wiring

Run appropriately sized conductors (THHN or similar) from the 208Y/120V panel to the buck-boost transformer input. For 60A, use a wire size appropriate for 75C terminations. You will need two hots, a neutral, and a ground. Connect the transformer output to the 60A subpanel. Use appropriate conduit or cable (e.g., EMT, MC cable) for all wiring runs, as required by local codes.4.

Grounding

Proper grounding is
critical. Ensure the ground wire is connected to the grounding bus bar in both the source panel and the subpanel. Follow all local code requirements for grounding.5.

Overcurrent Protection

Install a 60A two-pole breaker in the source panel to feed the transformer input. The 60A main breaker in the subpanel will provide overcurrent protection on the output side.6.

Labeling

Clearly label all panels, breakers, and the transformer.7.

Inspection

Have a qualified electrician inspect the installation
before energizing the circuit.

Important Safety Notes



Electricity is dangerous! If you are not completely comfortable working with electrical wiring, hire a qualified and licensed electrician. Improper wiring can lead to fire, injury, or death.

Local Codes

Always follow all applicable local electrical codes and regulations.


Professional Advice: This information is for general guidance only. A qualified electrician can assess your specific situation and provide tailored advice.Let me know if you have any more questions. Good luck! Flag for review

Previous Question Next Question