Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: hot tub close to a wall, needs equipotential bonding ?

User: Stevenfyeager, Location: United States, Indiana

Asked on: Friday, October 11, 2024 at 6:42 am EDT
Answered on: Thursday, March 6, 2025 at 3:46 am EST

Question: I tried to find where code requires an outside hot tub to have equipotential bonding under ground if it is located too close to a wall or structure. I couldn't find it. An electrical inspector told me this years ago. Thank you !

Okay, let's break down the requirements for equipotential bonding of outdoor hot tubs and address your question about proximity to walls or structures.

Understanding Equipotential Bonding

Equipotential bonding is a critical safety measure designed to minimize the risk of electric shock in and around a hot tub. The goal is to create an environment where all metallic parts and conductive surfaces within reach of a person in or near the hot tub are at the same electrical potential. This minimizes the voltage difference between these parts, thus reducing the likelihood of a dangerous current flow through the body if a fault occurs.

Key Sections of the NEC (National Electrical Code) Relevant to Hot Tub Bonding

The primary sections in the NEC that govern hot tub bonding are Article 680, Part VI specifically covers Spas and Hot Tubs. Here's a summary: 680.42(A) Bonding

This is the core requirement. It mandates that the following parts be bonded together:
All metal parts of the hot tub structure. All metal conduit and piping within 5 feet horizontally of the inside walls of the hot tub and that are not separated from the hot tub by a permanent barrier. All metal surfaces that are within 5 feet horizontally of the inside walls of the hot tub and are not separated from the hot tub area by a permanent barrier. Electrical equipment associated with the hot tub (pumps, heaters, lights, etc.).

680.42(B) Bonding Conductor Size

Specifies the size of the bonding conductor, generally No. 8 AWG copper.

680.26 Equipotential Bonding

This is the section that requires that the perimeter surface be bonded.


680.26(B) Perimeter Surface Bonding

NEC 680.26(B) covers perimeter surface bonding for pools and spas. The intent is to create an equipotential plane around the pool or spa to further reduce shock hazards. Here's the breakdown:

General Requirement

The perimeter surface extending 3 feet horizontally from the inside walls of the pool or spa must be bonded.


Surface Types

This applies to concrete, paving stones, and other conductive surfaces.

Bonding Methods

A solid copper conductor (typically No. 8 AWG) is used to form a grid under the perimeter surface. This grid is connected to the pool or spa's bonding grid and to the equipment grounding conductor. For existing installations, alternative methods like bonding the reinforcing steel in concrete are permitted.

Addressing Your Specific Questions
1. Underground Equipotential Bonding Near Walls/Structures

You're right, the NEC doesn't specifically call out a different bonding requirement solely based on proximity to a wall or structure. The distance requirement is based on the distance from the inside walls of the hot tub, regardless of whether a wall is nearby.2.

Why the Inspector's Statement?
Here's a possible explanation for what the inspector told you: Misinterpretation/Oversimplification

The inspector might have been oversimplifying the concept to ensure compliance. If a hot tub is close to a wall, there's a higher likelihood that metallic objects (e.g., metal siding, metal door frames, metal pipes) within 5 feet of the hot tub's
inside walls would also be close to the wall. These metallic objects would then need to be bonded.

Local Amendments

Some jurisdictions amend the NEC with stricter requirements. It's possible your local area had a stricter rule in place.

Emphasis on 680.26

The inspector might have been emphasizing the importance of perimeter bonding (680.26(B)). Even though it's not
specifically about walls, the perimeter bonding requirement effectively creates an equipotential zone around the hot tub, and the presence of a wall could influence how that zone is implemented. Because of the 3' perimeter surface bonding requirements. The presence of a wall requires it to be a perimeter surface.

Preventative Measure

The inspector might have been encouraging you to go above and beyond the minimum code requirements for added safety, especially if there were unusual circumstances (e.g., a very old house with questionable wiring, a history of electrical issues).

In summary

The NEC requires bonding of metallic parts within 5 feet of the inside walls of the hot tub, regardless of the presence of a wall or structure. Perimeter surface bonding (680.26(B)) creates an equipotential zone extending 3 feet horizontally from the inside walls of the hot tub. There is no specific NEC rule that solely triggers additional bonding requirements based on proximity to a wall. Always check with your local electrical inspector for any local amendments or interpretations of the NEC.

Recommendations
1. Consult the Latest NEC

Always refer to the most recent edition of the NEC adopted by your jurisdiction.2.

Local Inspector

Discuss your specific installation with your local electrical inspector before you begin the work. They can clarify any local requirements and ensure your installation meets all applicable codes.3.

Licensed Electrician

Hire a qualified, licensed electrician experienced in hot tub installations. They will be familiar with the NEC and local codes and can ensure the bonding is done correctly and safely.4.

Documentation:
Keep records of all inspections and electrical work performed.Disclaimer: I am an AI chatbot and cannot provide professional electrical advice. Always consult with qualified professionals for any electrical work or code interpretations. Flag for review

Previous Question Next Question