Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Inspector: four 12-2 cables require a two gang box

User: Stevenfyeager, Location: United States, Indiana

Asked on: Friday, October 11, 2024 at 4:22 pm EDT
Answered on: Thursday, March 6, 2025 at 3:47 am EST

Question: Today, the inspector failed my 22.5 cu inch outlet box with four 12-2 NM cables, and made me change it to a 2 gang box. For decades, I had been doing this. He said 4 12-2 cables = 8 X .225, plus one .225 for the grounds plus two .225 for the duplex receptacle. = 24.7 cu inches. I guess I'm never too old to learn.

You've got a great attitude! It's commendable that you're open to learning even after years of experience.Your inspector's calculation is correct, based on the NEC (National Electrical Code). Here's a breakdown: Each 12-2 NM Cable

Each current-carrying conductor within the cable counts. A 12-2 NM cable has two current-carrying conductors (black and white) and a grounding conductor (bare copper). For box fill calculation purposes, the NEC considers the cable a 2-wire fill. Four 12-2 cables therefore, has eight conductor equivalents


Grounding Conductors

All grounding conductors entering the box are counted as one conductor.

Device (Receptacle)

Each receptacle counts as two conductor equivalents.


Total Calculation

8 conductors (4 x 12-2 cables) = 8 x 0.225 cu. in. = 1.8 cu. in. Grounding conductors = 1 x 0.225 cu. in. = 0.225 cu. in. Receptacle = 2 x 0.225 cu. in. = 0.45 cu. in.

Total = 2.475 cu. in.


Therefore, a box marked with at least 2.475 cu. in. is required.Here are the NEC rules that pertain to the box fill calculations

NEC 314.16(A) Conductor Fill.
314.16(A)(1) Standard Boxes. Standard boxes shall be listed as to their cubic inch capacity, and the maximum number of conductors shall be calculated in accordance with 314.16(A)(1) through (5). Exception

The wire fill table in 314.16(B) shall be permitted to be used only for boxes that are part of a manufactured wiring system or are of the types described in Table 314.16(A).

314.16(A)(1) Conductor Fill Calculation.
The volume of a box shall be the total volume, as marked in the box, and the fill calculation shall be as follows: (1) Each conductor that originates outside the box and terminates inside the box shall be counted as one conductor volume. Each conductor that originates inside the box and terminates outside the box shall be counted as one conductor volume. (2) A conductor passing through the box without splice or termination shall not be counted. (3) Each conductor that originates and terminates entirely inside the box shall not be counted. (4) Device Fill. For each yoke or strap containing one or more devices, a volume allowance equal to twice the volume allowance required by 314.16(A)(1) shall be made for each conductor attached to a device contained in the yoke or strap. (5) Equipment Grounding Conductor Fill. Where up to four equipment grounding conductors enter a box, the volume allowance shall be based on the largest equipment grounding conductor entering the box. Where more than four equipment grounding conductors enter a box, the volume allowance shall be based on the total volume of all equipment grounding conductors.314.16(B) Box Fill Calculations. The maximum number of conductors permitted in a box shall be calculated in accordance with Table 314.16(B).

Table 314.16(B) Allowable Fill for Standard Boxes| Conductor Size (AWG) | Volume Allowance Required per Conductor (in.³)

-----------------------|------------------------------------------------
14 | 2.00
12 | 2.25
10 | 2.50
8 | 3.00
6 | 5.00 |Important Considerations



Box Markings

Always check the cubic inch capacity stamped inside the outlet box. This is the official capacity you must adhere to.

Device Yokes

The inspector correctly accounted for the device yoke of the receptacle.


Overcrowding

Overfilling a box is a safety hazard. It can lead to overheating, insulation damage, and potential fire.*

Amendments

Local jurisdictions may have amendments to the NEC.

Why the Change Now?


Codes are updated regularly to reflect new understandings of safety and technology. It's possible previous inspectors were less strict or that the code interpretation has been refined.By following these guidelines and consulting the latest edition of the NEC, you can ensure your wiring practices are safe and compliant. Flag for review

Previous Question Next Question