User: Jimcassidy, Location: Texas
Asked on: Saturday, October 12, 2024 at 6:20 am EDT
Answered on: Thursday, March 6, 2025 at 3:48 am EST
Question: Helping here in Florida - we have a church service that is down. I arrived late last night and will take a look at the service but I’m told it is a 240 V delta center tap, 3 phase 4 wire. Our generator has many configurations - but not 240 V delta center tap.The service has a gutter with a current transformer type meter that has 4 -3 pole disconnects tapped from a gutter.I’d like to give them temporary power for their worship service tomorrow & connect our 230 kV generator - what advice would you give?I am an old electrician who went through my apprenticeship in the 1980’s. Passed the my licensing again in the last year in Oklahoma as an unlimited electrician to help with a Christian Organization but have not worked in the field on a daily basis for many years.What caution & advice would you give?
Okay, let's get this church back up and running for their service tomorrow. Given your situation and experience, here's a breakdown of how to approach this, focusing on safety, feasibility, and providing temporary power
Understanding the Problem & Your Resources
240V Delta Center-Tapped (High-Leg Delta)
This is a very common older service type. It has a couple of potential issues. One phase (the "high leg," often painted orange) will have a higher voltage to ground (around 208V) than the other two (120V to ground). This is the KEY to understanding why you can't directly connect a standard generator. Mixing up phases can immediately damage equipment. You need to isolate the generator from the existing system.
Your 230kV Generator (Assumed to be kW, not kV)
Assuming you have a generator with multiple voltage configurations, the goal is to get it configured to a voltage that can safely feed part of the church's load. A much smaller portion and not connected to the same existing 240V delta center-tapped load.
Safety First!1. Verify Service is OFF
Confirm the main disconnect(s) for the 240V delta service are OFF.
Double-check this with a meter. You do NOT want backfeeding from your generator into the existing grid or the faulty service. Lock out and tag out (LOTO) the main disconnect(s) if possible. If there's no LOTO, ensure the disconnects are visibly in the OFF position and clearly marked.2. Qualified Help
While you have experience, consider if you can get a qualified electrician with recent hands-on experience with 240V delta systems to assist. A second set of eyes and expertise is invaluable.3.
Personal Protective Equipment (PPE)
Wear appropriate PPE, including safety glasses, insulated gloves, and arc-rated clothing if you suspect any potential for arcing.4.
Generator Placement
Place the generator in a well-ventilated area, away from combustible materials, and where exhaust fumes won't enter the building. Ensure it's properly grounded.5.
Fuel Safety
Handle fuel safely, away from ignition sources.
Steps to Provide Temporary Power (Assuming 230kW Generator)
This is a multi-step process and requires careful planning. The goal is to create a separate temporary power system.1.
Identify Essential Loads
Critically important. What absolutely needs power for the service? Lights? Sound system? A single HVAC unit? Simplify as much as possible. Avoid trying to power everything. Calculate the total ampacity of the essential load, and the individual circuit amptacity.2.
Generator Voltage Configuration
The MOST COMMON other voltage configuration on a 230 kW generator would be either
120/208V 3-Phase Wye OR 120/240V Single Phase or perhaps a 277/480V 3-Phase Wye. You need to determine WHICH of these (or other) configurations your generator has. Consult the generator's manual. The manual will tell you how to configure the generator for the output you need. 120/208V 3-Phase Wye
This is a common and safer option. You can run some equipment on 120V, but you cannot use 240V equipment without a step-up transformer.
120/240V Single Phase
Simpler to wire for smaller loads, but limited in capacity compared to 3-phase.
277/480V 3-Phase Wye
Don't use this. It will be too high of voltage.
Other Voltage Configurations
Consult generator manual.3.
Temporary Distribution Panel
You MUST use a temporary distribution panel fed from the generator. This panel will have breakers for the circuits you are creating for your essential loads. Consider 120V (for lights, sound) and/or a 240V Single Phase option (for a small HVAC or other)4.
Wiring
Run appropriately sized extension cords (heavy-duty, contractor-grade) or temporary wiring from the temporary distribution panel to the essential loads.
Do not overload circuits. Use a clamp meter to verify load current. Use a multi meter to verify voltage under load.5. Grounding
Proper grounding is critical. Ensure the generator is grounded according to the manufacturer's instructions. Connect the grounding electrode conductor (GEC) from the generator to a suitable grounding electrode (ground rod). Bond the generator frame to the grounding terminal in the temporary distribution panel.6. Testing
Before powering any equipment, carefully test the voltage at the temporary distribution panel and at each outlet you've created. Verify correct voltage and polarity.7.
Load Management
Start the generator and gradually add the loads, monitoring the generator's output. Do not exceed the generator's rated capacity.
Specific Cautions & Advice
NEVER directly connect the generator to the existing 240V delta system. This will cause serious damage and could create a dangerous situation. High-Leg Delta Confusion
The "high leg" is a real hazard. Be absolutely sure you know which phase it is and avoid it!
Neutral Bond
Make sure the generator's neutral is properly bonded (if it requires bonding). Consult the generator manual. If the generator is supplying power to a separate structure, there is very likely to be NO neutral bond at the generator.
Overloads
Overloading the generator can damage it and the equipment connected to it.
Backfeeding
Be vigilant about preventing backfeeding into the utility grid.
Example Scenario (Using 120/208V 3-Phase Wye Generator)
1. Configure your generator to 120/208V 3-Phase Wye.
2. Run heavy-duty extension cords from the generator to the sound system, and stage lighting.3. Verify voltage at the outlets with a meter.
4. Start the generator and gradually power up each piece of equipment.5. Keep a close eye on the generator's load meter.
Important Considerations
Permits
Check if a temporary generator permit is required by your local authorities.
Notify the Utility
Consider notifying the utility company that you are using a generator, especially if the main service is still connected (even if disconnected).
Documentation
Take photos of the connections and document the steps you take.
Disclaimer: This information is for guidance only and should not be considered a substitute for professional electrical advice. Consult with a qualified electrician for on-site assistance and code compliance. Your experience from the 80's is a great foundation, but electrical codes and practices have evolved significantly. Working with electrical systems is inherently dangerous, and improper procedures can result in serious injury or death. Proceed with caution and prioritize safety.Good luck getting the church service back up and running! Flag for review