Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Underground Systems subject to storm surges

User: augie47, Location: Tennessee

Asked on: Saturday, October 12, 2024 at 7:48 am EDT
Answered on: Thursday, March 6, 2025 at 3:48 am EST

Question: How do underground HV systems react to storm surge (flooding)?Can flooded pad transformers be dried out or do they need replacement ?

Let's break down how underground High Voltage (HV) systems and pad-mounted transformers react to storm surge flooding.

Underground HV Systems and Storm Surge

Underground HV systems are generally more resilient to storm surge and flooding than overhead systems, but they are not immune. Here's a breakdown of the reactions and potential issues:

Initial Resistance



Submersion

Most underground HV cables are designed to be watertight and capable of operating when submerged. The insulation is specifically chosen to withstand wet conditions, even saltwater.

Protection

Underground vaults and manholes, where splices, switches, and other equipment are housed, are designed to be watertight. They are sealed to prevent water ingress.


Reduced Direct Impact

Unlike overhead lines, underground cables are not directly exposed to wind damage from storms.

Potential Problems During/After Flooding



Water Ingress into Vaults/Manholes

Even with good sealing, prolonged and high-level flooding can overwhelm the seals on vaults and manholes. If water gets in, it can cause several problems:

Short Circuits/Faults

Water (especially saltwater) is conductive. It can create short circuits between phases or to ground, leading to immediate faults and power outages.


Equipment Damage

Submerged equipment (switchgear, transformers, splices) can suffer corrosion, insulation degradation, and mechanical damage.

Contamination

Floodwaters carry debris, silt, chemicals, and other contaminants. These contaminants can deposit within the vaults/manholes and on the equipment, causing long-term corrosion, insulation tracking, and reduced equipment lifespan.


Buoyancy Issues

In extreme flooding, empty or partially filled underground vaults can become buoyant, potentially damaging surrounding infrastructure and cable connections.

Erosion

Floodwaters can erode the soil around underground cables and vaults, undermining their support and potentially exposing them to damage.


Grounding Issues

Flooding can affect the grounding system, leading to improper grounding and potential safety hazards.

Saltwater Intrusion

Saltwater intrusion into the surrounding soil can accelerate corrosion of buried metallic components (conduits, cable shields).


Post-Flood Actions



De-Energization

As a safety precaution, utilities will often de-energize underground sections that have been flooded to prevent accidents and further damage.


Inspection

Thorough inspection of vaults, manholes, and cable runs is crucial to assess the extent of the damage and contamination. This often involves video inspections and electrical testing.

Cleaning and Flushing

Vaults and manholes need to be pumped out, cleaned, and flushed to remove contaminants.


Equipment Testing

Electrical testing (insulation resistance tests, hi-pot tests) is performed on cables and equipment to identify damaged components.

Repairs/Replacements

Damaged cables, splices, transformers, and switchgear must be repaired or replaced.


Grounding Verification

The integrity of the grounding system must be verified and restored.

Sealing Improvements

After a flood event, utilities often upgrade the sealing of vaults and manholes to better withstand future flooding.

Flooded Pad-Mounted Transformers: Drying Out vs. Replacement


Whether a flooded pad-mounted transformer can be dried out and salvaged or needs replacement depends on several factors:
Water Type

Saltwater contamination is much more damaging than freshwater. Saltwater is highly conductive and corrosive.

Submersion Time

The longer the transformer is submerged, the more water penetrates the core and windings, and the more corrosion occurs.


Water Level

Was it a shallow flood, or was the transformer completely submerged?

Transformer Age and Condition

Older transformers with pre-existing insulation weaknesses are more vulnerable to damage from flooding.


Severity of Contamination

Was the floodwater clean, or was it heavily contaminated with silt, oil, chemicals, or debris?

Transformer Type and Construction

The design of the transformer influences how easily water can penetrate and how easily it can be dried.

General Guidelines



Saltwater Submersion = High Probability of Replacement

Saltwater intrusion is almost always a death sentence for a transformer. The corrosion and insulation damage are often too severe to be economically repaired.

Freshwater Submersion (Short Duration)

If the transformer was submerged in freshwater for a relatively short time (e.g., less than 24 hours) and the water was relatively clean, there is a
chance it can be dried out and restored.

Extensive Contamination = Likely Replacement

If the transformer was submerged in heavily contaminated water (e.g., sewage, oil, chemicals), the cost of cleaning and restoring it may exceed the cost of replacement.

Drying Out Procedure (if attempted)

If drying out is considered, it must be done carefully and professionally to avoid further damage:1.

Safety First

De-energize and disconnect the transformer completely. Ensure it is properly grounded before starting any work.2.

External Cleaning

Thoroughly clean the exterior of the transformer to remove mud, debris, and contaminants.3.

Oil Sampling and Testing

If it's an oil-filled transformer, take an oil sample and have it analyzed for water content, contaminants, and dielectric strength. Badly contaminated oil must be drained and replaced.4.

Internal Inspection

Open the transformer (carefully) and inspect the internal components for water damage, corrosion, and contamination. Take pictures to document the condition.5.

Water Removal

Remove standing water from the tank.6.

Drying Process



Forced Air

Use warm, dry air to circulate through the transformer core and windings. Monitor the temperature carefully to avoid overheating and damaging the insulation.


Vacuum Drying

Apply a vacuum to the transformer tank to draw out moisture. This is a more effective method than forced air but requires specialized equipment.

Heat

Use external heaters (carefully controlled) to warm the transformer tank and encourage moisture evaporation. Again, temperature control is crucial.7.

Insulation Resistance Testing (Megger)

Regularly monitor the insulation resistance of the windings to ground as the transformer dries. The resistance should increase as the moisture content decreases.8.

Oil Processing (if applicable)

If the transformer is oil-filled, the oil may need to be processed through a vacuum dehydrator or filtration system to remove moisture and contaminants.9.

Final Testing

After drying, perform a full set of electrical tests, including:
Insulation Resistance (Megger) Turns Ratio Winding Resistance Hi-Pot (High Potential) Test Impulse Testing (if available)

Replacement is Recommended If

The transformer was submerged in saltwater. The transformer was submerged for an extended period (several days). The transformer was severely contaminated. Internal components show significant corrosion or damage. Insulation resistance does not improve significantly after drying. The transformer fails any of the final electrical tests. The cost of drying out and repairing the transformer exceeds the cost of replacement. The transformer is old or has a history of problems.

Important Considerations



Qualified Professionals

All inspection, testing, drying, and repair work on HV transformers should be performed by qualified and experienced professionals with specialized equipment and expertise.


Safety

HV equipment is dangerous. Strict safety procedures must be followed to prevent electrical shock and other hazards.

Documentation

Keep detailed records of all inspections, tests, and repairs performed on the transformer.


Insurance:
Contact your insurance company promptly to report the damage and discuss coverage options.In summary, while underground HV systems are more robust to storm surge than overhead systems, they are not invulnerable. Flooding can cause significant damage. Flooded pad-mounted transformers may be salvageable with careful drying procedures, but saltwater submersion and extensive contamination often necessitate replacement. Proper inspection, testing, and professional expertise are essential for assessing the damage and determining the appropriate course of action. Flag for review

Previous Question Next Question