Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Greenlee 755 pump

User: Crash117, Location: Nevada

Asked on: Saturday, October 12, 2024 at 3:20 pm EDT
Answered on: Thursday, March 6, 2025 at 3:50 am EST

Question: Hello all. Just picked up this used Greenlee 880 bender with a Greenlee 755 pump but it will not build up pressure. I’ve used these plenty in the past and am familiar with how it works. Unfortunately I’ve never had to try to repair one. Any insights on where to check it out would be appreciated. The ram will move about an inch but as soon as it builds up resistance it just won’t go any further. It just stays in that position. It takes quite a lot of handle throws just to get it to move that small amount until it stops. Thanks for any help

Okay, let's troubleshoot your Greenlee 880 bender with a 755 pump. Based on your description, it sounds like you're losing pressure somewhere. Here's a breakdown of potential causes and how to check them, starting with the easiest and most common

I. Pump (Greenlee 755): Likely Culprit
1. Check the Oil Level

This is the first and easiest thing. Low oil is the most common cause of pressure problems.


How

Find the oil fill port on the pump (usually a screw or cap). With the pump on a level surface, remove the fill port and check the level. It should be within the specified range (usually indicated on the pump or in the manual).

What to do

If low, use only hydraulic oil specified for Greenlee pumps (check your manual, but it's often ISO 46 or similar). Do
not use ATF (automatic transmission fluid). Top it off. Bleed the system (see below).

2. Check the Oil Condition

Look at the oil. Is it milky, frothy, or contaminated? Contamination can clog valves and prevent proper pressure buildup.

How

After checking the level, dip a clean screwdriver or dipstick into the oil and examine it.


What to do

If the oil is contaminated, you'll need to drain and flush the reservoir and replace the oil. Consider replacing the filter (if equipped).

3. Bleed the System

Air in the hydraulic lines can prevent proper pressure buildup.


How

Most Greenlee pumps have a bleed screw (usually on the pump body). Loosen the bleed screw slightly (just enough for air to escape). Pump the handle a few times. Tighten the bleed screw when only oil comes out (no more bubbles). Be careful - oil will spray!

4. Suction Tube/Screen Check

Inside the oil reservoir is a suction tube that pulls oil into the pump. It might have a screen filter on the end. This can get clogged.


How

You'll likely need to drain the oil to access this. Look inside the reservoir. If you see a tube leading to the bottom, that's it. Carefully remove it and inspect the screen.

What to do

Clean the screen thoroughly with solvent. If the tube itself is damaged, replace it. Reassemble and refill with clean oil.


5. Internal Pump Leakage (Most Common issue)

The pump itself may have worn seals or valves, causing internal leakage and preventing it from building pressure. This is the most likely problem given your description.

How

This is harder to diagnose without disassembly. Listen closely to the pump while you're pumping the handle. Do you hear any hissing or gurgling sounds
inside the pump body? Does the pump body get excessively hot?

What to do

This usually requires disassembly of the pump. If you're mechanically inclined, you can try to find a repair kit (seals, O-rings) for your 755 pump online. Greenlee sells them or aftermarket kits are often available. Otherwise, consider taking it to a hydraulic repair shop.

6. Pressure Relief Valve

The pump has a pressure relief valve to prevent over-pressurization. If this valve is stuck open, it will prevent pressure buildup.


How

Locate the relief valve (it will be a small screw or knob somewhere on the pump body, often with a lock nut). Try loosening the lock nut and turning the screw in and out slightly (a small adjustment). Retighten the lock nut. Then try pumping the handle again.

What to do

If adjusting doesn't work, the valve might be damaged or have debris stuck in it. Disassembly and cleaning might be required, or replacement.

II. Bender (Greenlee 880): Less Likely, But Possible
1. Cylinder Seal Leak

The ram cylinder itself might be leaking internally, causing the pressure to bypass the ram and prevent it from extending fully.

How

Look for oil leaking
around the ram cylinder as you try to bend. Internal leakage can be harder to spot, but if the ram gets significantly hot during operation and moves very slowly, it's suspicious.

What to do

This requires disassembly of the bender cylinder and replacement of the seals. Again, repair kits are often available.

2. Hose Leaks

Carefully inspect the hydraulic hose connecting the pump to the bender for any leaks, cracks, or damage.


How

Look closely at the hose itself, especially at the fittings. Flex the hose and check for leaks.

What to do

Replace the hose if you find any damage. Ensure the fittings are properly tightened.

III. Troubleshooting Steps
1. Start with the Oil

Check level and condition first.2.

Bleed the System.
3. Listen to the Pump

Pay attention for unusual noises.4.

Inspect the Hose

Look for leaks.5.

Adjust the Relief Valve (Carefully).
6. If still no pressure

You are most likely looking at a pump rebuild at this point.

Important Safety Notes



Hydraulic fluid is under high pressure. Exercise extreme caution when working on hydraulic systems.
Always wear safety glasses. Relieve pressure before disconnecting any hydraulic lines.* If you're not comfortable working on hydraulic systems, take it to a professional repair shop.

By systematically checking these areas, you should be able to pinpoint the cause of your pressure loss and get your Greenlee bender back in working order. Good luck! Flag for review

Previous Question Next Question