Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Dewatering Conduit

User: TwoBlocked, Location: Bradford County, PA

Asked on: Saturday, October 12, 2024 at 7:47 pm EDT
Answered on: Thursday, March 6, 2025 at 3:50 am EST

Question: Got a small job coming up. Part of it is to "dewater" some underground 2" conduit that got flooded. Nothing is in them, just for future use. No caps had been installed on the stub ups, so the flood waters was free to enter, and they are full.Haven't done this before. Figure to start with blowing them out with a shop vac. Once most of the water is out, keep blowing into one end while holding a hand over the other to build up pressure and then release it to "burp" more water out.Here's my question: Should I stop after burping, or should I try to pull some kind of piston through to get all the water out? I'm concerned with getting it stuck if there is a lot of mud, or if the conduit broken under ground. I'm sure some of you fine folks have good advice for me.

Okay, this is a pretty common problem, and your approach is a good starting point. Here's a breakdown of the advice based on experience

1. Your Initial Approach (Shop Vac and Burping):
Shop Vac First

Absolutely. A shop vac is the first and best tool. Use a narrow nozzle to create concentrated suction. Try to get a good seal.


Burping

This is a good idea. The pressure will help dislodge stubborn water pockets.

2. When to Consider Alternatives



If Shop Vac/Burping Fails

If you're still getting significant water after repeated attempts with the shop vac and burping, then you need to consider other options.


If you Suspect Debris

If you suspect a lot of mud or silt is in the conduit, more aggressive methods will be necessary.

3. Alternatives if Shop Vac/Burping Isn't Enough



Compressed Air



Caution

Compressed air can be dangerous. Never put your face directly in line with the open end of the conduit. Wear safety glasses. Control the pressure!

Method

Use an air compressor with a nozzle that fits (or can be adapted to fit) snugly into the conduit. Use short bursts of air, rather than a continuous stream. This will help "chop" the water and debris. This is often the most effective method.


Pressure

Start with low pressure (20-30 psi) and increase gradually only if needed. Excessive pressure could damage the conduit.

Water Hose



Caution

Only use this if the conduit drains to an area where the water won't cause damage.

Method

Insert a water hose into one end of the conduit. Turn the water on to flush out any debris.


"Piston" or "Sponge"



Pros

A good way to physically push out debris.


Cons

As you identified, the risk of getting stuck is real.

How to Reduce Risk



Choose the Right Material

Use a tightly wound rag/towel that is almost the diameter of the pipe.

Lubrication

Wetting the piston/sponge will allow it to slide easier.


Attach a Strong Pull Cord

Use a strong nylon rope or fish tape attached securely to the piston. Make sure the knot is very secure.

Gradual Force

Pull gently and steadily. Don't yank.


Rotation

Try twisting the rope/fish tape as you pull. This can help loosen any obstructions.

Back and Forth

If you encounter resistance, don't force it. Try pushing the piston back and forth a short distance to see if you can work it past the obstruction.


If it Gets Stuck

If you can't move it with reasonable force, STOP. Don't break the rope or fish tape. You'll need to dig to expose the conduit at the point of the obstruction.

Fish Tape with Rag



Method

Wrap a small, tight rag around the end of a fish tape. This can sometimes be pushed through the conduit to help dislodge debris. It's less likely to get stuck than a full piston.

Professional Conduit Cleaning Services



When to Consider

If you have a very long run of conduit, multiple obstructions, or are concerned about damaging the conduit, it might be worth hiring a professional with specialized equipment. They often have tools like water jetting systems or conduit snakes with cleaning attachments.

4. Important Considerations



Safety

Wear safety glasses and gloves throughout the process.


Drainage

Make sure the water has a place to drain away from any sensitive equipment or areas.

Inspect the Conduit

Before starting, visually inspect the exposed ends of the conduit for any obvious damage (cracks, kinks, etc.). This can help you assess the risk of it being damaged underground.


Identify Conduit Run

If possible, try to determine the path and length of the conduit run. This can help you anticipate potential problem areas.

Documentation

Document the process you used and any problems you encountered. This will be helpful for future reference.


Consider the Cost of Replacement

In some cases, especially if the conduit is damaged or heavily obstructed, it might be cheaper and easier to just abandon the existing conduit and run a new one. Weigh the cost of your time and potential problems against the cost of replacement.

Recommendation:


Start with the shop vac and burping. If that doesn't work, try the compressed air (with caution). If you still have problems and suspect significant debris, the piston/sponge is the next option, but proceed very carefully. If you get stuck or feel uncomfortable, consider hiring a professional or abandoning the conduit and running a new one.Good luck! Flag for review

Previous Question Next Question