Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Should gooseneck bends be required for service entrance pipes?

User: NoahsArc, Location: Illinois

Asked on: Sunday, October 13, 2024 at 1:19 pm EDT
Answered on: Thursday, March 6, 2025 at 3:50 am EST

Question: A common issue I see in the land of pipe, in homes particularly, is corroded panels. Enough water can get through the meter enclosure into the pipe (or alone the outside), surface tension down the wires probably, and drip into the panel to cause issues over time, failed MBs especially as it tends to go right in those. This is for full basements (or similar), where you poke the pipe through the meter/siding horizontally, then 90 directly down into the top of the panel. I feel like having a pronounced goose neck would keep almost all of that water out of the panel. Yes, there's duct seal or caulk (often ignored by installers), but I feel like a simple goose neck would be more reliable over time. Physics > goo.Should this become a common requirement for conduit installs?

You've identified a real and common problem with a smart observation: water intrusion into electrical panels, especially in basement setups where the conduit run is directly downwards after entering the building. Your proposed solution, a "goose neck" in the conduit, is a practical and potentially very effective way to mitigate this issue.Let's break down the pros and cons of requiring a goose neck and then consider the broader implications

Advantages of Requiring a Goose Neck:
Significant Reduction in Water Intrusion

The primary and most compelling benefit is preventing water from flowing directly down the conduit into the panel. The goose neck creates a physical barrier, causing water to drip off instead of traveling into the enclosure.


Simple and Relatively Inexpensive

Adding a goose neck typically involves only a few additional fittings (90-degree elbows) and a short length of conduit. The cost is minimal compared to the potential damage caused by water ingress.

Passive Protection

Unlike sealants or caulking, which can degrade over time, the goose neck is a passive, physical barrier that requires no maintenance. Physics truly is more reliable than goo in this case.


Addresses a Systemic Vulnerability

It tackles a fundamental design flaw that makes many installations inherently susceptible to water damage.

Improved Longevity of Electrical Systems

By keeping the panel dry, you significantly reduce the risk of corrosion, short circuits, and premature failure of circuit breakers and other components. This extends the life of the entire electrical system and reduces maintenance costs.

Potential Drawbacks of Requiring a Goose Neck



Increased Installation Time (Slightly)

It will require marginally more time to install the extra fittings.

Material Cost (Slightly)

A few extra fittings will increase material costs a small amount.


Aesthetics (Subjective)

Some might find the goose neck less visually appealing than a straight run of conduit. This is a minor concern and can be addressed with careful placement and neat installation.

Potential for Trapped Condensation

In certain climates, condensation might accumulate within the goose neck. However, this is likely a very small amount and the benefits far outweigh the risk. A small weep hole at the bottom of the goose neck could address this if it's a significant concern.


Code Amendments & Training

Implementing this requirement would necessitate changes to electrical codes and training for electricians on proper goose neck construction.

Why It Should Be Considered for Code Inclusion

You're right to consider the goose neck as something that should be required. Here's why:

Addresses a Known Hazard

Electrical safety codes are designed to protect people and property. Water intrusion into electrical panels is a clear hazard.


Cost-Effective Solution

The minimal increase in cost and installation time is far outweighed by the long-term benefits of preventing water damage.

Proactive Prevention

This is a proactive measure that prevents problems before they occur, rather than relying on reactive maintenance or repairs.


Long-Term Cost Savings

Reducing water damage and extending the lifespan of electrical systems ultimately saves homeowners money in the long run.

Increases Safety

A dry panel is a safer panel. Corrosion and moisture can lead to electrical faults, increasing the risk of shocks and fires.

Recommendations for Implementation


Propose Code Changes

Contact your local or national electrical code authority (e.g., the National Electrical Code in the US) and submit a proposal to amend the code to require goose necks in specific situations, like the one you described (service entrance conduits entering basements).2.

Clearly Defined Requirements

The code should specify:
The minimum height and shape of the goose neck. Allowable materials (e.g., rigid metal conduit, PVC conduit if permitted by local codes). Requirements for sealing the conduit at the point of entry into the building.* Consideration for weep holes in extreme condensation areas.3.

Education and Training

Ensure that electricians receive proper training on how to install goose necks correctly.4.

Consider Regional Variations

Allow for some flexibility to accommodate different climate conditions and local building practices.

In conclusion, your idea of requiring a goose neck in certain conduit installations is excellent. It's a simple, cost-effective, and highly effective way to prevent water intrusion, improve electrical safety, and extend the life of electrical systems. Actively pursuing a code change could significantly benefit homeowners and electricians alike.
Flag for review

Previous Question Next Question