Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Is this a classified location

User: dm9289, Location: Pennsylvania

Asked on: Monday, October 14, 2024 at 8:40 am EDT
Answered on: Thursday, March 6, 2025 at 3:52 am EST

Question: This was recently installed at the factory I work in and I had some questions about hazard and NEC compliance.This area is a chemical storage containment area.Hazards are corrosive, plus harmful to people and wildlife.A spill would not be normal. Chemical is transferred by fork lift from this area to the area used.Transformer and panel are nema 3R.Conduit is threaded RMC.Should this area by classified? I think noIs the nema 3R equipment adequate? I think perhaps 4XInside this area do the receptacle outlets require GFCI protection?Thank you in advance I think this could be a good learning experience for me.

Okay, let's break down the NEC (National Electrical Code) and hazard considerations for your chemical storage containment area. This is a good exercise in applying the Code.

Should this area be classified (Hazardous Location)? Likely NO, based on the information you provided. Hazardous location classification (Class I, II, or III, and Division 1 or 2 or Zones) is based on the probability of flammable vapors, combustible dusts, or easily ignitable fibers being present in ignitable concentrations. You stated that a spill would not be normal. Your assessment that spills are not normal, and given that the chemicals you are dealing with are corrosives (rather than flammable liquids or gases), this doesn't sound like a typical hazardous location situation. Important Note

This determination is absolutely critical and requires a thorough hazard assessment. You need to consider things like: The volatility of the chemicals. The amount of chemical stored. The ventilation of the area. The likelihood of leaks or spills due to equipment failure or human error. The presence of ignition sources.

Who Makes the Determination?

The owner of the facility is responsible for designating the hazardous location classification, with the advice of a qualified professional (e.g., a chemical engineer, safety engineer, or electrical engineer experienced in hazardous locations).

Is the NEMA 3R Equipment Adequate?
Potentially Inadequate, NEMA 4X is better choice. NEMA 3R is designed for protection against rain, sleet, snow, and external ice formation. It's not specifically designed for chemical resistance. Given the corrosive nature of the chemicals, NEMA 4X (or even higher, depending on the specific chemicals) is a better choice. NEMA 4X provides protection against corrosion, hose-directed water, and windblown dust and rain. The X suffix denotes corrosion resistance. NEC Requirements

NEC 110.11 requires electrical equipment to be suitable for the environment. The presence of corrosives makes NEMA 3R questionable.

Do Receptacle Outlets Require GFCI Protection?
YES, most likely. NEC 210.8(B) generally requires GFCI protection for receptacles in commercial and industrial locations. NEC 210.8(B) GFCI Protection for Personnel

Applies to 125-volt through 250-volt receptacles rated 50 amperes or less. This is a
very broad requirement, encompassing almost all common receptacles in commercial and industrial settings.

If the area is considered a wet or damp location GFCI protection is required.
The best practice is to provide GFCI protection in this situation.Additional Considerations and Recommendations Safety Data Sheets (SDS)

Thoroughly review the SDS for each chemical stored in the area. Pay close attention to the hazards, reactivity, and proper handling procedures.

Written Hazard Assessment

Document a formal hazard assessment for the area. This should be reviewed and updated periodically. Involve safety personnel, chemical engineers, and electrical professionals in this process.


Signage

Clearly post signage indicating the chemical storage area, the potential hazards, and any required PPE (Personal Protective Equipment).

Spill Control

Have a spill control plan in place, including readily available spill kits and trained personnel.


Grounding and Bonding

Ensure proper grounding and bonding of all electrical equipment to minimize the risk of static electricity buildup and potential ignition sources.*

Qualified Electrical Contractor

Consult with a licensed and experienced electrical contractor familiar with industrial installations and hazardous locations.

In summary


Prioritize a formal hazard assessment.
This will drive the proper classification (or non-classification) of the area.2. Upgrade to NEMA 4X (or better) for corrosion resistance.3. Provide GFCI protection for all applicable receptacles.4. Document everything and consult with qualified professionals.Disclaimer: I am an AI chatbot and cannot provide professional engineering or legal advice. This information is for educational purposes only. Always consult with qualified professionals for specific applications and compliance with applicable codes and regulations. Flag for review

Previous Question Next Question