User: rlundsrud, Location: chicago, il, USA
Asked on: Monday, October 14, 2024 at 5:48 pm EDT
Answered on: Thursday, March 6, 2025 at 3:54 am EST
Question: I posted this in lighting but I haven't received any responses.Can a 0-10 volt class 2 lighting control circuit be reclassified as a class 1 circuit if the manufacturers literature only identifies it as a class 2? In NEC parlance, does 725.130 take precedence over 110.3(b) if all conditions for 725.130 are met? Would the manufacturer need to specify it as being class 1 compliant so it can be installed in the same conduit as the 120 volt power wiring.
You're right to be cautious about this. Mixing low-voltage control wiring with line-voltage power wiring is a common point of concern and potential code violation. Here's a breakdown of the NEC considerations and why you're unlikely to be able to "reclassify" a Class 2 circuit simply by meeting the conditions of 725.130
Understanding the Classes
Class 1 Circuits (Article 725, Part II)
Class 1 circuits are power-limited (Article 725.21) or remote-control and signaling circuits (Article 725.25) that generally operate at higher voltages and power levels than Class 2 or Class 3 circuits.
Class 2 Circuits (Article 725, Part III)
Class 2 circuits are power-limited in both voltage and current. This limitation is designed to reduce the risk of electrical shock and fire. Power is limited in accordance with 725.41.
Manufacturer's Listing and 110.3(B)
NEC 110.3(B) is crucial: Listed or labeled equipment shall be installed and used in accordance with any instructions included in the listing or labeling. This means the manufacturer's designation as a Class 2 circuit is generally binding.
Why You Can't Usually "Reclassify" a Class 2 Circuit1. Manufacturer's Intent and Testing
The manufacturer has designed, tested, and listed the equipment as Class 2. This listing is based on specific voltage, current, and power limitations, as well as safety considerations. Changing the classification effectively voids the listing.
2.
Safety and Listing Requirements
Class 1 circuits have different wiring methods, overcurrent protection, and insulation requirements than Class 2 circuits. If the manufacturer only intended for Class 2 wiring methods, it's unlikely the conductors are rated for a Class 1 installation.3.
Enforcement and Liability
An inspector will typically go by the manufacturer's listing. Deviating from it puts you at odds with the code and potentially exposes you to liability if something goes wrong.
NEC 725.130 and Separation Permitted Mixing with Class 1 Circuits
NEC 725.130 allows Class 2 and Class 3 circuits to be installed with Class 1 circuits only if one of the following conditions is met:
(A)
The Class 1 circuit conductors are installed using the wiring methods in Chapter 3.
(B)
The Class 2 and Class 3 circuit conductors are separated from the Class 1 circuit conductors by a barrier or by maintaining a separation of at least 2 inches.
(C)
Class 2 and Class 3 circuits are installed in raceways suitable for use with electric light, power, or Class 1 circuits.
Your Specific Situation Manufacturer's Literature
If the manufacturer's documentation only identifies the lighting control circuit as Class 2, then 110.3(B) prevails. You must install it according to the Class 2 requirements.
Conduit Sharing
You cannot run the Class 2 0-10V wiring in the same conduit as the 120V power wiring unless the manufacturer specifically states the 0-10V control wiring complies with the requirements in Chapter 3 for Class 1 wiring, even though it is listed as Class 2.
Compliance
Compliance with 725.130 alone does not automatically make a Class 2 circuit behave like a Class 1 circuit. If your 0-10V is truly a Class 2 circuit and the manufacturer does not specify Chapter 3 wiring methods, you'll need to keep it separate from your 120V wiring as per 725.130(B).
In summary
You can't just reclassify a Class 2 circuit as Class 1 based on meeting certain conditions in the NEC. The manufacturer's listing (and 110.3(B)) is paramount. To run the 0-10V wiring in the same conduit as the 120V wiring, you need to show that the manufacturer specifies it can be installed using Chapter 3 wiring methods.
Recommendations1. Consult the Manufacturer
Contact the lighting control manufacturer directly. Ask if their 0-10V wiring is suitable for installation in a raceway with power wiring, or if they have instructions that permit or prohibit this type of installation. Get this in writing.2.
Provide Separation
If the manufacturer doesn't explicitly allow conduit sharing, you'll need to separate the Class 2 and Class 1 circuits.3.
Involve Your Inspector: Discuss your plans with your local electrical inspector before you start the installation. They can offer valuable guidance and ensure your installation meets local requirements. Flag for review