Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: HVAC Engineering question for Bathroom Exhaust

User: Michael1985, Location: toronto

Asked on: Tuesday, October 15, 2024 at 7:53 am EDT
Answered on: Thursday, March 6, 2025 at 3:56 am EST

Question: Hi everyone. hoping to get some input regarding my bathroom exhaust fan Panasonic 90CFM. I live in a condo and currently renovating the bathroom. The existing 5" duct runs vertical from the fan to the outside 35 feet with (2) 90 degree elbows. I will attempt to reposition the fan to remove (1) 90 degree elbow. That said, my question is.1. Do I require a booster for a bathroom exhaust fan that has a 35 foot run? Seeing that the condo developer never installed one, I assume it was not required to code.FYI, the Dryer fan has a booster and it also is 35 feet run.2. I would like to reduce the 5" duct down to 4" duct upon entering the bathroom to the actual fan outlet. The existing 5" duct from outside will remain until it reaches the bathroom at which point I would like to reduce it to 4". Will there be a significant impact loss by reducing at the fan?Greatly appreciate any input.Thanks,M

Okay, let's break down your bathroom exhaust fan situation.1. Do I require a booster for a bathroom exhaust fan that has a 35-foot run? Technically (without knowing exact specifics), you likely don't require a booster according to code. Building codes often specify minimum CFM requirements and maximum duct run lengths for exhaust fans. Since the developer didn't install one, it likely met the code at the time of construction. However, a booster could significantly improve performance. A 35-foot run, especially with elbows, creates a lot of static pressure (resistance to airflow). While a 90 CFM fan might be rated for that flow under ideal conditions, in reality, it's probably delivering much less CFM at the exhaust point after the 35-foot run. The key consideration is how effective the existing fan is at removing moisture. Do you have issues with condensation, mold, or lingering humidity after showers? If so, the fan isn't performing adequately. Here's a simplified way to think about it

Imagine trying to blow air through a 35-foot straw versus a short straw. It's much harder to get the same airflow with the longer straw. The longer duct run is like that straw.

Since your Dryer fan has a booster
it suggests the developer realized a booster was required on long runs. Keep in mind that dryer fans are generally much more powerful than bathroom exhaust fans and create more static pressure than bathroom fans.

Therefore, I recommend assessing your fan's performance before deciding not to install a booster, or test after you have completed installation of new fan and duct before installing a booster.2. Reducing the 5" duct to 4" at the fan connection



This is generally
not recommended and will negatively impact performance.
You are creating a bottleneck in the system. Airflow Physics

Airflow is like water in a pipe. Restricting the pipe (reducing the diameter) increases the velocity of the air but decreases the overall volume that can pass through. This creates pressure loss, which your fan has to overcome.

Significant Impact Loss

The impact will be more significant than you might think. Reducing duct size
increases static pressure dramatically. Even if you were to install a booster, the restriction might make the booster work harder than necessary and not deliver its full potential benefit.

Why avoid it?
Even a good 90 CFM fan, after the 35-foot run, is likely delivering less than 90 CFM. Restricting it further will make it even worse. Alternatives

Try to avoid reducing duct size if at all possible.

Recommendations
1. Prioritize Reducing Elbows

Removing that one 90-degree elbow is good. Even try to use (2) 45-degree elbows instead of a single 90-degree elbow. This will reduce static pressure.2.

Keep the 5" Duct the Entire Run

This is the most important. Don't reduce to 4" at the fan. If physically impossible, find ways to install larger than 4" duct to reduce static pressure.3.

Measure Airflow (if possible)

After you've installed the fan and made the elbow improvements, try to measure the airflow at the exhaust point in the bathroom. There are relatively inexpensive anemometers (airflow meters) that you can use. You can also do a "tissue test" – hold a tissue near the fan; it should be strongly sucked up against the grill.4.

Consider an Inline Booster Fan (if needed)

If, after optimizing the duct run and verifying the fan is properly installed, you still find that the fan isn't removing moisture adequately, consider adding an inline booster fan in the middle of the run closer to the exhaust vent to the outside.5.

Consider a more powerful fan

Panasonic offers fans with higher CFM ratings. This would allow you to deliver more CFM after the long run.6.

Consider insulated ducts
Insulated ducts will prevent condensation.

In Summary Keep the duct size consistent. Reduce elbows as much as possible. Evaluate the fan's performance after making improvements to the duct run. If needed, consider a booster fan or larger fan.Good luck with your renovation! Flag for review

Previous Question Next Question