Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: modifying contents of an Exd enclosure

User: bubu, Location: Pittsburgh

Asked on: Tuesday, October 15, 2024 at 9:49 am EDT
Answered on: Thursday, March 6, 2025 at 3:56 am EST

Question: Hello,First of all, I'm mostly used to the European standards, so bear with me if this is a silly question.I'm involved in a project where the contractors are wanting to replace the components within a certified Exd enclosure. Basically there's a little lcd display that they want to replace with an led one that can be networked rather than the RS485 one they have.In Europe this is a no go since there's things like the temperature rating and the available internal volume which will be affected by the modification, but I'm told this isn't a concern when it comes to NFPA/UL requirements and I find it slightly odd. I don't have access to the UL1203 to understand the requirements but was wondering if someone can shed some light on this?

You're right to be concerned. While the US and European approaches to Ex equipment certification share the same fundamental goal – preventing explosions – the execution and specific requirements differ. It's definitely not a "free for all" in the US, and simply swapping components in an Exd enclosure without proper evaluation and recertification is almost certainly not permitted under any system, including NFPA/UL.Here's a breakdown of why your concerns are valid and how the US system works

Why Your Concerns are Valid in the US (and Globally)
Temperature Rating

Heat dissipation of the new LED display and networking components
absolutely matters. Exd (flameproof) enclosures are designed to contain an internal explosion. If the internal temperature exceeds the certified temperature class (e.g., T6, T5, etc.), it can lead to: Increased explosion pressure (exceeding enclosure design limits). Higher surface temperatures capable of igniting surrounding explosive atmospheres. Deterioration of seals and other critical enclosure components.

Internal Volume

The available internal volume
does matter, indirectly. While UL1203 doesn't explicitly define a maximum volume for all Exd enclosures (as some European standards might do), the enclosure is tested with specific components inside. Adding new components changes the characteristics of the internal explosion, potentially exceeding the enclosure's design limits.

Intrinsically Safe Circuits

If the new networking component (e.g., Ethernet) isn't inherently designed to be explosion-proof, it introduces a potential ignition source inside the enclosure.

Original Certification Validity

Modifying a certified Exd enclosure
voids the original certification unless the modifications are explicitly permitted and documented by the certification body (e.g., UL, FM).

Safety and Liability

Ignoring proper procedures puts personnel at risk and opens the door to significant legal liability if an incident occurs.

How the US System (NFPA 70/NEC and UL Standards) Addresses This
NFPA 70 (National Electrical Code - NEC)

This is the legally enforceable standard governing electrical installations in the US. Article 500 and subsequent articles (501, 502, 505, etc.) cover hazardous locations and dictate that equipment must be
listed (i.e., certified) for the specific hazardous location in which it's used.

UL Standards

Underwriters Laboratories (UL) develops standards for safety. UL1203 is the primary standard for Explosion-Proof Electrical Equipment for Use in Hazardous (Classified) Locations. However, other standards might also apply depending on the specific components being added.

Listing/Certification

Equipment is
listed by a Nationally Recognized Testing Laboratory (NRTL) like UL, FM, CSA, etc. The NRTL tests the equipment to the relevant UL standard(s) and, if it meets the requirements, issues a listing (e.g., a UL listing mark). This listing indicates that the equipment is suitable for use in the specified hazardous location.

UL1203 Key Considerations for Exd Enclosures



Strength of Enclosure

The enclosure must withstand the pressure developed during an internal explosion without transmitting the explosion to the surrounding atmosphere.


Flame Path

The enclosure must have flame paths (gaps between mating surfaces) of specific dimensions to quench any flame that might escape during an internal explosion. These dimensions depend on the gas group (IIA, IIB, IIC) and the enclosure volume.

Temperature Class

The enclosure must not exceed its temperature class rating under normal or abnormal operating conditions.


Component Spacing and Materials

UL1203 specifies requirements for the spacing of electrical components and the materials used in the enclosure.

Section 90.7 of the NEC - Examination of Equipment for Safety
Basically says that if you modify the equipment it needs to be evaluated for safety to the original standards by a competent third party. Field Modifications

The NEC generally prohibits field modifications that affect the equipment's listing. Article 500.8(F) often refers to this. This doesn't mean modifications are impossible, but they require careful consideration and often involve:

Manufacturer Involvement

Ideally, the original equipment manufacturer (OEM) should be consulted. They may have approved modification procedures.


NRTL Evaluation

The modified equipment must be evaluated by an NRTL to determine if it still complies with the relevant UL standards. This might involve additional testing and potentially a supplemental listing.

Documentation

Thorough documentation of the modifications and the NRTL's evaluation is crucial.

Practical Steps to Take
1. Stop the Modification

Immediately halt any unauthorized modifications.2.

Consult with a Qualified Expert

Engage a qualified electrical engineer or consultant experienced in hazardous location design and US regulations. They can help you navigate the regulatory requirements.3.

Contact the OEM

Reach out to the original manufacturer of the Exd enclosure. They may have pre-approved solutions for upgrading the display and communication interface.4.

Contact an NRTL

Discuss the proposed modifications with an NRTL like UL or FM. They can advise on the steps required to maintain or obtain a listing for the modified equipment.5.

Alternative Solutions

Consider if a completely new, certified Exd enclosure with the desired features (LED display and networking) might be a more cost-effective and compliant solution.6.

Documentation

Keep very good records of all communication, assessments, tests, and any changes made.

In summary,
while the US system has some nuances compared to European ATEX/IECEx, it
absolutely* does not permit arbitrary component swaps in Exd enclosures. Proper evaluation, testing, and certification by a qualified NRTL are essential to ensure safety and compliance with the NEC and UL standards. Your initial assessment is correct. Modifying a certified enclosure without proper evaluation and re-certification is a serious safety risk and likely a violation of US regulations. Flag for review

Previous Question Next Question