Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 4 wire to generator ?

User: sparkync, Location: North Carolina

Asked on: Tuesday, October 15, 2024 at 12:55 pm EDT
Answered on: Thursday, March 6, 2025 at 3:57 am EST

Question: I have a customer who I am going to be running a line from the "Main electrical panel" to a "generator inlet" box on the outside. I've noticed that the "50 amp inlet boxes" I see, don't have a "ground terminal screw", only a "ground jumper" to the box, mounted directly to the box, with no provision for another wire. I got to thinking that the "house ground" is already in place through the water pipes, and ground rods, then it seems I would only have to run a 3 conductor cable instead of a 4 conductor to the inlet box, since the generator would only be supplying the hots and neutral, since the "ground" is already available in the electrical panel. Am I thinking right according to Code? The run is going to be around 80ft., so I need to know if I'm thinking right, to save money on the wire. Normally, I would run 4 wires. I thought it strange the inlet boxes did not have a grounding lug available in the box. Thanks for the input.

Okay, let's break down the situation and address your question regarding the grounding of a generator inlet box. It's absolutely critical to understand this correctly for safety and code compliance. Your line of thinking is NOT correct and could create a very dangerous situation.

Here's a detailed explanation

1. Why a 4-Wire System is Required for Generator Connections:
Safety First

The purpose of a dedicated ground wire (equipment grounding conductor - EGC) is to provide a low-impedance path for fault current back to the source (in this case, the generator)
and the main panel. This path is crucial for tripping the breaker or fuse in the event of a short circuit. Without it, a fault could energize the metal chassis of appliances or equipment, creating a severe shock hazard.

Separation of Neutral and Ground

Modern electrical code (NEC) requires a separate neutral and ground conductor for generator connections. The neutral is a current-carrying conductor under normal operation, while the ground is only supposed to carry current during a fault. Bonding (connecting) the neutral and ground at multiple points can create circulating currents and potentially dangerous voltages on the grounding system.

Generator as a Separately Derived System

When the generator is operating and powering the house, it becomes a "separately derived system." This means that the grounding requirements change slightly. The generator needs its own grounding system (usually through a grounding electrode - a rod driven into the earth)
or must have a properly installed and sized equipment grounding conductor connecting it to the main service panel's grounding system.

2. Why You
Cannot Rely on Existing House Grounding for the Generator



Water Pipes and Ground Rods are Not Sufficient for Fault Current

While water pipes and ground rods are important for grounding the electrical service to the earth, they are not designed to carry significant fault current. They have high impedance (resistance) and won't reliably trip a breaker in a short circuit. They are primarily for static dissipation and lightning protection, not for equipment grounding.

Potential for Neutral-Ground Voltage (Neutral Drop)

If you rely on the existing house grounding for the generator's ground, any voltage drop on the neutral conductor will appear as a voltage between the neutral and ground at the generator. This can cause equipment malfunction and even damage.

3. Understanding the Generator Inlet Box



The Ground Jumper

The ground jumper you see in the inlet box is not the entire grounding system. It's there to bond the metal enclosure of the inlet box to the equipment grounding conductor. This is a safety measure to ensure the box itself is not energized in the event of a fault.

The Missing Ground Lug

The fact that there's no
obvious lug doesn't mean it's not intended to be grounded. Look closely. The green jumper wire, which is connected to the box, IS where you would connect your grounding conductor. In other words, you must "pig tail" your wire to make the connection with the ground jumper.

4. Code Requirements (NEC - National Electrical Code)



NEC 250.30
outlines the requirements for grounding separately derived systems (like generators). It requires a bonding jumper between the generator's neutral and the generator's frame unless the generator is connected to the building's grounding electrode system via a properly sized equipment grounding conductor. NEC 250.130 details the requirements for equipment grounding. It is important to be able to "read" your ampacity chart to be in compliance with NEC 250.122 for the required size of your EGC.5. How to Properly Ground the Generator Inlet Box


Run a 4-wire cable

Use a 4-wire cable (hot-hot-neutral-ground) from your main electrical panel to the generator inlet box.
This is non-negotiable for safety and code compliance.2.

Connect the wires correctly

Connect the two hot wires to the appropriate terminals in the panel and the inlet box. Connect the neutral wire to the neutral busbar in the panel and the neutral terminal in the inlet box. Connect the ground wire to the ground busbar in the panel and "pig tail" it to the ground wire that is "jumped" to the box itself inside the inlet box.3.

Proper Wire Size

For a 50-amp circuit over 80 feet, you will likely need #6 AWG copper wire, but always consult the NEC ampacity tables and adjust for voltage drop. Use the appropriate type of wire (THHN/THWN in conduit, or appropriate cable type like UF or NM-B if allowed by local code).

In Summary

You must run a 4-wire cable. Do not cut corners on safety. The existing house grounding system is not adequate for the generator. Connect the ground wire to the ground busbar in the main panel and "pig tail" it with the ground jumper attached to the box.

Important Recommendations



Consult a Qualified Electrician

This is not a DIY project for someone without experience. Electrical work is dangerous and requires a thorough understanding of the NEC.


Get a Permit and Inspection

Obtain the necessary permits from your local building department and have the installation inspected to ensure it meets code. This is a crucial step to ensure safety and avoid potential liability issues.

Proper Transfer Switch

Be sure you are installing a properly rated and listed transfer switch (manual or automatic) to prevent backfeeding onto the utility grid. Backfeeding is extremely dangerous for utility workers and is illegal.


Understand Your Generator:
Familiarize yourself with your generator's grounding requirements. Some generators have a floating neutral and may require a different grounding configuration. Consult the generator's manual and a qualified electrician.Taking shortcuts on electrical work can have catastrophic consequences. Don't risk your safety or the safety of others. Get professional help and ensure the installation is done correctly. Flag for review

Previous Question Next Question