Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Neutral line posts facing outward at outlets, is this dangerous? What would it take?

User: Electrical_Hazard, Location: Mexico

Asked on: Wednesday, October 16, 2024 at 1:57 am EDT
Answered on: Thursday, March 6, 2025 at 3:59 am EST

Question: As I mentioned yesterday in the post where I asked for help, I am faced with these outward facing n line posts of the blue wire.My understanding since early life was not to touch the electric outlet insides because it can be dangerous.What situation would it take for this N line to get somebody? A Surge at the same time they are touching water and touching the n line post?This can't possibly be a 100 percent safe situation as I heard in here the electrons know which way to go?I figure they must think the dangerous part is the ground post on the cable of the device or equipment. That is why they do this this way and not the way I was knowing before in USA. Is this because of the type of configuration of their electrical system being the 220 rather than the 130? Purely for my scientific purposes I am not looking up?

Okay, let's break down the situation and address your concerns about the "N line" (likely the Neutral line) posts you're seeing. I want to be absolutely clear: working with electrical systems can be dangerous, and it's always best to consult a qualified electrician for any electrical work.Understanding the Neutral Line In a properly functioning electrical system

The Neutral line is intended to carry current back to the source after it has passed through a load (like a light bulb or appliance). Ideally, it should be at or very close to 0 volts relative to ground. It's
designed to be relatively safe to touch under normal circumstances.

Why it's NOT always safe

Here's why you cannot assume the neutral is always safe:

Fault Conditions

If there's a fault in the wiring (like a short circuit), the Neutral line can become energized with dangerous voltage. This is especially true if the grounding system isn't properly installed or maintained.


Improper Wiring

Incorrect wiring can cause the Neutral to carry current it shouldn't, potentially creating a shock hazard.

Shared Neutral

In some (often older or poorly designed) systems, multiple circuits might share a single Neutral wire. If one of those circuits has a fault, the Neutral could carry dangerous current.


Voltage Drop

Under heavy load conditions (lots of appliances running), there can be a voltage drop on the Neutral line. While it might not be a full 120V or 220V, even a lower voltage can be dangerous, especially if you're wet or have a pre-existing medical condition.

Situations That Could Make the Neutral Line Dangerous
Simultaneous Contact with a Live Wire

This is the most obvious danger. If you're touching a live (Hot/Line/Phase) wire and the Neutral, you're providing a path for current to flow through your body. The severity of the shock depends on the voltage and the current.


Faulty Appliance/Equipment

If an appliance has a fault that causes its metal casing to become energized, touching the Neutral and the casing could provide a path for current. This is why proper grounding of appliances is crucial.

Damaged Wiring

If the insulation on a wire is damaged, exposing the conductor, touching that exposed conductor (even if it's the Neutral) could be dangerous, especially if there's a fault in the system.


Wet Conditions

Water significantly reduces your body's resistance to electricity. Touching any electrical conductor while wet is extremely dangerous. Even a small voltage can become lethal.

"Surge" is less of a concern here

While a surge can damage equipment and potentially create a fault that energizes the neutral, the immediate danger is from
sustained voltage on the neutral due to a wiring issue or fault.

Why Grounding is Important
Grounding provides a path for fault current

In the event of a short circuit or insulation failure, the ground wire provides a low-resistance path for the current to flow back to the source. This high current flow should trip a circuit breaker or blow a fuse, quickly disconnecting the power and preventing a shock.

Grounding helps keep equipment at a safe potential

By connecting the metal parts of appliances and equipment to ground, you ensure that they remain at a safe voltage relative to the earth. This prevents them from becoming energized in the event of a fault.

220V vs. 120V Systems
Higher voltage = Greater Risk

A 220V system (common in many parts of the world outside North America) presents a higher risk of electric shock than a 120V system. This is because the higher voltage can drive more current through your body if you come into contact with it.

Neutral and Phase Configuration

The specific configuration of the electrical system (e.g., single-phase, three-phase) and how the Neutral is derived (e.g., grounded neutral) can affect the behavior of the Neutral line and potential hazards.

"Electrons Know Which Way to Go"
This is a highly simplified way of thinking about electricity and can be misleading. Electrons will flow through any available path, taking the path of least resistance. Your body, especially when wet, can provide a lower-resistance path than the intended circuit, leading to a shock.

Why the system is the way it is



Safety is the design intent

The electrical systems used today are designed to prioritize safety by using grounding, circuit breakers, and insulation to minimize the risk of electric shock.


It is NOT foolproof

Electrical systems are not perfect, and faults can occur. This is why it is important to have properly installed wiring, use grounded appliances, and follow safe electrical practices.

In Summary
1. Do NOT assume the Neutral is always safe.2. Water increases the risk dramatically.3. Contact with a live wire and the Neutral simultaneously is extremely dangerous.4. Grounding is a critical safety feature.5. Higher voltage systems are more dangerous.6. Always consult a qualified electrician for electrical work.

You are right to be cautious and ask questions. It's much better to be safe than sorry when dealing with electricity. Flag for review

Previous Question Next Question