Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Underground communications wire. Best practice

User: fastline, Location: midwest usa

Asked on: Wednesday, October 16, 2024 at 12:50 pm EDT
Answered on: Thursday, March 6, 2025 at 4:00 am EST

Question: I don't usually go underground with communications but looks like some Cat6 will need to go in underground conduit. Curious what the best practice is? Being a "wet location", I am not sure if gel filled cable will be required?

You're right to be cautious about running Cat6 underground! Here's a breakdown of best practices and considerations for your underground Cat6 installation

1. The Right Cable:
Gel-Filled/Flooded/Outdoor Rated Cat6

This is the

MOST important
factor. You ABSOLUTELY NEED gel-filled or flooded cable that's specifically rated for outdoor/direct burial use. This is non-negotiable. Standard indoor Cat6 will fail rapidly underground due to moisture.
Gel-filled (flooded) cable has a gel or petroleum-based compound inside the cable jacket that surrounds the conductors. This gel prevents water from wicking down the cable if the outer jacket is damaged. Outdoor-rated cable also typically has a more robust jacket that's UV resistant and designed to withstand temperature fluctuations and harsh environments. Shielded vs. Unshielded (STP vs. UTP)



Shielded (STP) cable
is generally recommended for outdoor/underground runs, especially if you're running it near power lines or other sources of electromagnetic interference (EMI). The shielding provides extra protection against signal degradation. Unshielded (UTP) cable can be used, but it's generally not recommended for underground runs, especially if you're near potential sources of interference. If you do use UTP, make absolutely sure it's gel-filled/outdoor-rated. Jacket Material



Polyethylene (PE)
jackets are common for outdoor/direct burial cable due to their excellent moisture resistance and UV protection. PVC (Polyvinyl Chloride) jackets are also sometimes used, but PE is generally preferred for direct burial. Make sure the PVC jacket is specifically rated for outdoor use.2. Conduit is Essential



Why Conduit?
Conduit provides physical protection for the cable against damage from rocks, roots, rodents, and shifting soil. It also makes it easier to replace the cable in the future if needed. Type of Conduit



Rigid PVC Conduit (Schedule 40 or Schedule 80)

This is the most common and generally recommended type of conduit for underground network cable runs. It's durable, relatively inexpensive, and easy to work with. Schedule 80 is thicker and offers more protection than Schedule 40.

Electrical Metallic Tubing (EMT)

While EMT can be used, it's not the best choice for underground applications. It's more prone to corrosion than PVC. If you
do use EMT, it must be approved for direct burial and properly grounded.

Flexible Conduit (Liquidtight Flexible Nonmetallic Conduit - LFNC)

This can be used for short runs or bends, but it's not ideal for the entire run due to its flexibility and potential for damage. Use it sparingly to make connections to equipment or around obstacles. Use appropriate fittings for LFNC.

Conduit Size

Choose a conduit size that's large enough to easily pull the cable through without damaging it. A good rule of thumb is to have the cable occupy no more than 40% of the conduit's cross-sectional area. Consider future needs – could you need to run another cable through the same conduit later?


Conduit Depth

Local codes and regulations usually specify the minimum burial depth for conduit. Generally, you should bury PVC conduit at least 18 inches deep. Check your local electrical codes. Deeper is better, if practical, as it provides more protection.

Sealing the Conduit

Use conduit sealant (duct seal) at both ends of the conduit run to prevent water, dirt, and insects from entering. This is
crucial even with gel-filled cable. Also seal any joints in the conduit. Specific sealants are made for this purpose.

3. Installation Best Practices



Plan Your Route

Carefully plan the route of your underground run, avoiding areas where digging might occur in the future (e.g., flower beds, future construction zones). Consider marking the route with flags or stakes.

Trenching

Dig a trench of the appropriate depth. Remove any sharp rocks or debris from the trench that could damage the conduit.


Conduit Assembly

Assemble the conduit run, using appropriate fittings and connectors. PVC conduit requires PVC cement to join sections. Ensure all joints are properly sealed.

Cable Pulling

Use a cable pulling lubricant (approved for the cable and conduit type) to reduce friction and prevent damage to the cable jacket during pulling. Pull the cable gently and avoid excessive tension. Use a cable pulling grip (basket) to distribute the pulling force evenly. Consider using a pull string in the conduit for future cable pulls. Do not exceed the cable's bend radius. Too tight of a bend can damage the conductors.

Backfilling

Carefully backfill the trench, avoiding large rocks or sharp objects that could damage the conduit. Compact the soil as you backfill.

Grounding (for Shielded Cable)

If you're using shielded cable, properly ground the shielding at both ends of the run to prevent ground loops and provide optimal protection against EMI. Follow manufacturer's instructions and local electrical codes.


Testing

After installation, thoroughly test the cable run to ensure proper connectivity and performance. Use a cable tester to verify the wiring configuration and signal quality.

4. Important Considerations



Local Codes and Regulations

Always check with your local building and electrical codes before starting any underground wiring project. They may have specific requirements for burial depth, conduit type, and grounding. Permits might be required.


One-Call Before You Dig (811)

Before you start digging, call 811 (in the US) to have underground utilities located and marked. This is essential to prevent damage to existing utilities (gas, water, electric) and ensure your safety.

Distance

For long runs, you may need to consider signal attenuation (signal loss over distance). Cat6 has a maximum recommended length of 100 meters (328 feet). If your run is longer than that, you may need to use a repeater or switch to extend the signal. Fiber optic cable might be a better choice for very long distances.


Future-Proofing

Consider running extra conduit or a larger conduit than you currently need to accommodate future expansion or upgrades.

Example Scenario

Let's say you're running Cat6 from your house to a detached garage, a distance of 100 feet.1.

Cable

You'd purchase 120 feet (allowing extra length at each end) of gel-filled, outdoor-rated, shielded (STP) Cat6 cable with a PE jacket.2.

Conduit

You'd use 100 feet of 1" Schedule 40 PVC conduit, plus PVC cement, fittings, and conduit sealant.3.

Trench

You'd dig a trench 18 inches deep between the house and the garage.4.

Installation

Assemble the conduit, pull the cable through with lubricant, seal the conduit ends, and backfill the trench. Ground the shielding at both ends.5.

Testing

Test the cable to ensure proper connectivity.

In summary



Use gel-filled/outdoor-rated cable in conduit, bury it at the correct depth, seal the conduit, and follow all local codes. It's worth the extra effort to do it right the first time, as it will save you a lot of trouble and expense in the long run.
Flag for review

Previous Question Next Question