Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Surge Protection

User: Fernandomart14, Location: El Paso Tx

Asked on: Thursday, October 17, 2024 at 10:55 pm EDT
Answered on: Thursday, March 6, 2025 at 4:05 am EST

Question: Is surge protection required on a Main Panel when installing Pv System? Regardless if its been upgraded or not?

The requirement for surge protection on a main panel when installing a PV system depends on a few factors, primarily the specifics of the electrical codes and standards adopted in your location, and the equipment being installed. Here's a breakdown of the considerations

Generally Required, But with Exceptions:
NEC (National Electrical Code)

The NEC, which is widely used in the United States,
does generally require surge protection. Specifically, NEC 2020 and newer versions have stricter requirements.

NEC 2020 (and newer) - 230.67 Surge Protection

This section mandates surge protection at the service equipment (main panel) for dwelling units. There are some exceptions but most installations would require it.

NEC 690.12 - Rapid Shutdown

While not directly related to
surge protection, rapid shutdown requirements often mean disconnecting the PV system at the roof or near the array, and this can increase the need for surge protection at the main panel to protect against surges that might enter from other sources.

Why It's Important



Protecting Sensitive Electronics

PV systems often include inverters, monitoring equipment, and other electronic devices that are susceptible to damage from voltage surges (e.g., lightning strikes, utility switching). Surge protection helps to divert these surges away from the sensitive equipment.


Protecting Appliances/Loads in your Home

Even if the PV system itself is well-protected, surges can still enter the electrical system from the grid. Surge protection on the main panel helps protect all the electrical devices in the home.

Code Compliance

As mentioned above, the NEC (and similar codes) often
require surge protection to be installed, meaning it's not just a good idea, but a mandatory part of the installation.

Factors That Influence the Requirement/Selection of Surge Protection



Local Amendments to the NEC

Your local jurisdiction (city, county, or state) may have amended the NEC. Always check with your local electrical inspector or building department to determine the specific code requirements in your area.

Equipment Manufacturer Requirements

Some PV system manufacturers may require specific types of surge protection as a condition of their warranty. Check the product documentation for the inverter, combiner box, and other components.


Type of PV System

The type and size of the PV system can influence the need for surge protection. For example, a grid-tied system may be more vulnerable to surges from the grid than an off-grid system.

Risk Assessment

In some cases, a risk assessment may be performed to determine the likelihood and severity of surge events in a particular location. Areas with frequent lightning strikes or unstable power grids may benefit from more robust surge protection.


Existing Surge Protection

If the main panel already has a surge protection device (SPD) that meets current code requirements, it may not be necessary to add another one. However, it's important to verify that the existing SPD is properly rated and functioning.

Upgraded Panel vs. Non-Upgraded Panel



Generally Doesn't Matter

The requirement for surge protection is primarily based on the current code and the type of installation,
not whether the panel has been upgraded. If the codes being followed require surge protection, it is required whether the panel is brand new or decades old.

Condition of the Panel

An upgraded panel may be in better overall condition, which could improve the effectiveness of the surge protection device. Also, you may need to upgrade the panel to allow for the breaker spaces needed for the PV system as well as the surge protection device.

Recommendations


Consult with a Qualified Electrical Contractor

The best way to determine the specific surge protection requirements for your PV system is to consult with a licensed and experienced electrical contractor who is familiar with local codes and PV system installations. They can assess your site, review the applicable codes, and recommend the appropriate surge protection solution.2.

Check with Your Local Authority Having Jurisdiction (AHJ)

Contact your local building department or electrical inspector to confirm the code requirements in your area.3.

Review Equipment Documentation

Carefully review the product documentation for all PV system components to understand the manufacturer's recommendations and requirements for surge protection.

In summary, surge protection is typically required (especially with newer NEC editions) when installing a PV system on a dwelling. However, the specifics depend on local codes, equipment requirements, and a professional assessment of your electrical system. Always consult with qualified professionals to ensure compliance and safety.
Flag for review

Previous Question Next Question