Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 3000 hp 1800rpm, 4160v Synchronous (manufacturer Ideal) motor with 90 volt excitation system.

User: Simon05511, Location: Toledo

Asked on: Friday, October 18, 2024 at 1:42 pm EDT
Answered on: Thursday, March 6, 2025 at 4:06 am EST

Question: We just removed our motor and sent it off to the shop due to not being able to Sync. When the Rotor was removed and each of the 4 coils was tested, it was found that one of the coils on the rotor had a lower reading than the other three. Three of the rotor coils were .306-.310 ohms, and the fourth coil was .270.My questions,1. Would this cause the motor to not sync?2. Is there anything we could do to help it sync? increase Dc voltage during start up?

Okay, let's break down this situation and address your questions.

Understanding the Issue Rotor Coils

The rotor in your motor (most likely a synchronous motor) has coils that interact with the stator's magnetic field. These coils are energized to create a rotating magnetic field that "locks in" with the rotating magnetic field produced by the stator windings, achieving synchronism.


Coil Resistance

The resistance of a coil is a critical parameter. A lower resistance for one coil, compared to the others, suggests a possible shorted turn within that coil, a difference in coil winding, or potentially a connection issue.

Syncing Problems

Synchronous motors are designed to lock into the grid frequency. The "syncing" process involves getting the rotor speed close to the synchronous speed and then energizing the rotor coils to pull it into complete synchronism. If something is wrong with the rotor magnetic field strength and the fields are not uniform, it will cause Sync issues.

Answering Your Questions
1. Would this cause the motor to not sync? YES, it is very likely that this coil resistance imbalance is a significant contributor to your motor's inability to sync. Here's why: Uneven Magnetic Field

The lower resistance (.270 ohms) on one coil indicates that it's likely producing a weaker magnetic field compared to the other three. This imbalance disrupts the symmetrical and uniform magnetic field needed for proper synchronisation. The rotor's magnetic field is no longer uniform, making it difficult for the rotor to "lock in" with the stator's rotating magnetic field.


Torque Imbalance

The weaker coil will contribute less torque during the synchronization process. This can cause the rotor to oscillate or hunt around the synchronous speed without ever fully locking in.2.

Is there anything we could do to help it sync? increase Dc voltage during start up?
Increasing DC Voltage



In theory

Increasing the DC voltage to the rotor field during start-up might seem like a way to compensate for the weaker coil.

In practice: ABSOLUTELY DO NOT DO THIS.
This is not a good approach and could potentially damage the motor further: Exacerbated Imbalance

Increasing the voltage might push the good coils beyond their design limits, potentially damaging them and worsening the overall imbalance.

Overheating

The lower resistance coil could overheat due to increased current, potentially causing insulation failure and further damage.


Not a Fix

It's treating the symptom, not the cause. The fundamental problem is the coil's integrity.

Things NOT to do
Attempt to change the resistance of the good coils to match the bad coil This is absolutely NOT recommended. This will result in your motor not operating correctly Better Approaches (While the Motor is at the Shop)



Trust the Professionals

Since the motor is at the shop, let them do their job. Explain that you are aware of the issue and are looking forward to a solution.

Coil Rewinding/Replacement

The most reliable solution is to rewind or replace the faulty coil. This restores the coil to its original specifications and ensures a balanced magnetic field.


Complete Rotor Rewind

In some cases, it might be more cost-effective or recommended to rewind the entire rotor. This ensures all coils are matched and in optimal condition.

Rotor Replacement

If the damage is extensive or beyond repair, replacing the entire rotor is the best option.


If the motor was still on site I would Recommend to you
Monitoring

During attempted startups, monitor the current in each rotor coil (if possible with your motor's instrumentation). This could confirm the lower current in the suspect coil.


Check Connections

Ensure all connections to the rotor coils are clean, tight, and properly made. A loose connection could add resistance and affect performance.

Mechanical Issues

While the coil issue is likely the primary cause, double-check for any mechanical issues that could be contributing to the syncing problems (e.g., bearing problems, excessive load).


Important Considerations



Documentation

Review the motor's nameplate data, service manuals, and any available test reports. This can provide valuable information about the motor's specifications and expected performance.


Expert Consultation

Rely on the expertise of the motor repair shop. They have the tools, knowledge, and experience to properly diagnose and repair the motor.*

Safety

Always follow proper safety procedures when working with electrical equipment. De-energize the motor and lock it out before performing any inspections or repairs.

In summary:


The difference in coil resistance is a significant issue that likely explains your motor's syncing problems. Repairing or replacing the faulty coil (or the entire rotor if necessary) is the correct course of action. Do NOT attempt to "band-aid" the problem by increasing voltage, as this could lead to further damage. Let the repair shop handle the problem. Flag for review

Previous Question Next Question