Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Adding an external ground to 2" LFMC

User: Carl24x, Location: Decatur MS

Asked on: Saturday, October 19, 2024 at 10:09 am EDT
Answered on: Thursday, March 6, 2025 at 4:09 am EST

Question: Looking to see what could be used to install an external ground on the outside of a piece of 2" LFMC in a class 1 Div 2 area. My flexible connectors do not have provisions to install a ground on them and are too thin to tap. It's been a while but i recall using something split that you could loosen the nut, install and retighten connector providing a means to install a ground. I wanted to see if anyone recalled the part i'm looking for while i continue to look.Thanks,

You're likely thinking of a grounding bushing or hub specifically designed for flexible metal conduit (FMC or LFMC) in hazardous locations. Here are a few types and considerations

1. Split Grounding Bushing (for Existing Connectors):
Description

This is likely what you're remembering. These are split in half (or more) allowing you to install them around an already installed connector. They clamp onto the outside of the conduit (typically on the connector itself) and provide a lug for attaching the ground wire.


Manufacturers

Look at manufacturers like:

O-Z/Gedney (Erickson)
: They make split grounding bushings specifically for hazardous locations. They'll likely have products certified for Class I, Division 2. Look for terms like "split grounding bushing," "hazardous location," and "FMC/LFMC." Appleton Crouse-Hinds Important Considerations



Material

Ensure it's made of a compatible material (e.g., copper-free aluminum, stainless steel) for hazardous locations.


Certification



This is CRITICAL.
The bushing MUST be specifically listed and labeled for use in Class I, Division 2 locations. Look for markings like "Class I, Div 2," "Ex," "UL listed for hazardous locations," or similar. Conduit Size

Make sure the bushing is the correct size for your 2" LFMC.


Connector Compatibility

While "universal," these bushings might fit some connectors better than others. Check the manufacturer's specifications.

2. Grounding Hub (for New Installations)



Description

If you haven't installed the connectors yet, this is often a better solution. Instead of a standard LFMC connector, you use a grounding hub that incorporates a grounding lug directly.


Manufacturers

The same manufacturers listed above make grounding hubs.

Important Considerations



Certification

Same as above - must be listed for Class I, Division 2.

Conduit Size

Get the correct size for your LFMC.


Thread Type

Ensure the hub has the correct thread type (NPT is common) to match your enclosure.

3. Other Options (Less Common in this Specific Scenario)



Grounding Locknuts

These are typically used for rigid conduit (RMC) or IMC, but some specialized versions
might be adaptable, but generally not the best for LFMC.

Direct Bonding

In some cases, you might be able to bond directly to the equipment enclosure using a listed bonding bushing or fitting. This is more about bonding the enclosure to the grounding system, not providing a grounding point on the flexible conduit run itself. This would require a listed fitting on the enclosure itself.

Why This Matters (Hazardous Location Considerations)



Sparking

In Class I, Division 2 areas, the concern is the
potential for flammable vapors or gases to be present. A poor ground connection can cause arcing or sparking if a fault occurs, which could ignite the atmosphere.

Code Compliance (NEC Article 501)

The National Electrical Code (NEC) has strict requirements for grounding and bonding in hazardous locations. Using the correct listed and labeled fittings is essential for compliance and safety.

Vibration/Movement

LFMC is often used in areas where there's vibration or movement. A robust grounding connection is needed to maintain continuity even with movement.

Steps to Take


Review the NEC (Article 501)

Make sure you understand the grounding and bonding requirements for Class I, Division 2 locations.2.

Consult the Equipment Manual

The equipment you're connecting the LFMC to may have specific grounding instructions.3.

Identify the Specific Connector

Knowing the manufacturer and part number of your existing LFMC connector will help you find a compatible grounding bushing (if that's the route you choose).4.

Contact Electrical Suppliers

Talk to suppliers that specialize in hazardous location electrical equipment. They can help you find the correct listed and labeled parts.5.

Inspect for Corrosion

If you're using existing equipment, check for corrosion on any grounding surfaces. Clean and treat as needed.6.

Proper Installation

Follow the manufacturer's instructions for installing the grounding bushing or hub. Torque connections to the specified value.7.

Testing

After installation, verify the ground connection with a low-resistance ohmmeter.

Safety First!
De-energize

Always de-energize the circuit before working on electrical equipment.

Qualified Personnel

Only qualified electricians should work on electrical systems in hazardous locations.


Permits:
Check local regulations for any required permits or inspections.Good luck with your installation! Remember to prioritize safety and code compliance. Flag for review

Previous Question Next Question