Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Is this a psychotic plan? It might just be...

User: carsongwalker, Location: Dallas, TX

Asked on: Monday, October 21, 2024 at 3:16 pm EDT
Answered on: Thursday, March 6, 2025 at 4:13 am EST

Question: Hello,Im trying to hook up power to my new office trailer, from a subpanel of a nearby shed. The office has 120V ligthing and receptacles, and a 240V A/C unit. The subpanel that I intend to use for the source is a 60A 415Y/240V 3-phase panel.It would probably be easiest to just get a ~25kva 240V to 240V-120V transformer and run the 240-120 split-phase panel on the office trailer as it is intended. Im trying to avoid this becasue I would like to reuse a cheap 5kva 240V to 120V single phase transformer I already have. The goal is to run the lighting and AC off the 5kva transformer while feeding the A/C unit directly with my already existing 240V at the subpanel. I am also adding an extra 240V receptacle at the office.I attached a layout of how I think this can work, but have concerns regarding the grounding and whether half of what I am doing is even allowed.To assist with the diagram, i will explain below...1. Install 3x 30A breakers in the sub panel.2. Run 3x lines of hot 10awg, 3x 10awg nuetrals, and a 10awg ground to the transformer in a single 3/4" conduit.3. Pass circuits from P1 and P2 through the transformer to the office panel, no connections.4. Connect P3 circuit to 5kva across H1/H3 and H2/H4 accordingly to get 120V on the secondary accross X4 and X1 (X2 and X3 connected). Tie ground to the transformer chassis.5. Feed 120V into office panel along with the other 2x 240V circuits, single conduit.6. Inside office panel, bond X1 (identified as the nuetral) from transformer to ground/nuetral bus. My understanding is this should be bonded despite being a sub panel since the 120 circuit is isolated. Drive a ground rod and connect to bus as well.7. With a ground ran between the ground/nuetral bar to each 240V circuit, one can connect to the existing AC wiring, the other circuit can go to the newly installed 240V receptacle on the exterior of the bulding.8. The 120V line will feed the already existing panel through a 30A breaker, the light and receptacles will be ran off 2x 30A breakers already inside the panel. They appear to share a nuetral (as the office came), and are accordingly on a shared double 30A breaker. Ground connected to the ground/nuetral.So this might seem like a stupid, and possibly horrible, way to do this. Might be fun to pick apart and tell me I have no business doing this.Thanks!

Okay, let's break down your proposed setup. You're right to be concerned about the grounding and safety of this configuration. This is a complex situation and needs careful consideration to avoid dangerous conditions.

General Concerns & Red Flags



Overcomplication

This setup is incredibly complicated and introduces multiple points of potential failure. It violates several basic electrical principles, especially regarding grounding and neutral configurations. It's like trying to solve a simple problem with an extremely complex and fragile machine.


Code Violations

This design will violate the NEC (National Electrical Code) and likely any local electrical codes. Trying to repurpose existing equipment into unsafe configurations can create liability and safety concerns. This will never pass inspection (and you should get an inspection!).

Safety Risk

Incorrect grounding and neutral connections can lead to shock hazards, fires, and equipment damage. You are mixing different voltage systems (3-phase supply, single-phase distribution) in a manner that creates significant potential for imbalance and dangerous current flow.


Transformer Mismatch

A 5kVA transformer will not be enough to run all the lighting and receptacles of the office.

Specific Issues with Your Proposed Setup (Numbered to match your description)


3 x 30A Breakers

While theoretically okay for feeding the transformer primaries, remember that you're dealing with a 3-phase system. Using only 30A breakers on the subpanel isn't the issue. You need to consider the overall loading of the 3-phase system.2.

Conduit Size

3/4" conduit might be too small depending on the specific type of wire you're using and the derating factors required due to the number of conductors in the conduit. Consult the NEC (National Electrical Code) for proper conduit fill calculations. Remember that it is common that ground wires need to be upsized to deal with potential fault currents. This may not be possible with your proposed conduit.3.

Passing Through the Transformer

This is not a safe/standard practice.4.

Transformer Connections and Output

Theoretically, a single-phase transformer can derive 120V from 240V. However, the real issue is the limited capacity. Even if you get the voltage correct, 5kVA (or 5000 volt-amps) translates to roughly 41.6 amps at 120V. That's not much for an entire office with lighting and receptacles, especially if you plan on using it for extended periods of time, or even just at its capacity.

Grounding to Chassis

Yes, you need to ground the transformer chassis for safety. The case of the transformer should be bonded to the grounding conductor.5.

Conduit Again

Same as point 2, verify conduit fill.6.

Neutral Bonding and Ground Rod



THIS IS A HUGE RED FLAG AND VERY DANGEROUS.
You should NEVER bond the neutral to ground in a subpanel unless it's the first disconnecting means after the service entrance. Bonding the neutral in the office trailer creates a ground loop, where current can flow on the grounding conductor. This presents a significant shock hazard and can cause nuisance tripping of breakers. Also, the neutral from the transformer is the neutral for the derived 120V system and should not be bonded again. This would create a paralleling neutral path through the ground.7. Connecting to Existing AC Wiring

I'm not sure how this will function, depending on how the AC unit is wired. I do know its unsafe without proper inspections and load balancing.8.

Shared Neutral

Sharing a neutral is allowed in some cases, BUT it must meet the requirements for a multiwire branch circuit. Typically, this requires a 2-pole breaker that disconnects both hot legs simultaneously. You also need to be extremely careful about load balancing on each leg of the circuit to avoid overloading the neutral conductor. Also, 30A breakers are excessive for lighting and receptacles. Typical circuits would be 15A or 20A, depending on the load.

Why This Is A Bad Idea (Recap)



Ground Loops

You're almost guaranteed to create ground loops, leading to potential shock hazards, equipment damage, and electrical noise.

Overloaded Transformer

A 5kVA transformer is likely undersized for the combined load of lighting, receptacles, and the AC unit. You'll likely trip breakers or damage the transformer.


Improper Grounding/Bonding

You are mixing 3-phase and single-phase systems in a dangerous way, and your proposed grounding scheme violates code and creates a shock hazard.

Code Violations

The entire setup is likely in violation of electrical codes, which are in place for safety.

The Right Way to Do This


Hire a Qualified Electrician

This is not a DIY project. Electrical work is dangerous and requires expertise to do it safely and correctly. A licensed electrician will be familiar with local codes and the NEC.2.

Run a Proper Feeder

Have the electrician run a properly sized 4-wire feeder (two hots, a neutral, and a ground) from the 3-phase panel to the office trailer. The size of the wire and breaker will depend on the calculated load of the office trailer, including the AC unit, lighting, and receptacles.3.

Install a Subpanel in the Office Trailer

Install a properly sized subpanel in the office trailer. This subpanel should have a separate neutral bus and ground bus (the neutral bus should
not be bonded to the ground bus).4.

Branch Circuits

Run individual branch circuits from the subpanel to the lighting, receptacles, and AC unit, using the appropriate wire gauge and breaker size for each circuit. The AC unit will be on a 240V circuit, and the lighting and receptacles will be on 120V circuits.5.

Use a properly sized Step Down transformer

If you would like to keep the transformer, it needs to be sized accordingly.

Key Considerations



Load Calculation

The most important step is to accurately calculate the total load of the office trailer, including the AC unit (consider its starting current), lighting, receptacles, and any other equipment you plan to use. This load calculation will determine the size of the feeder, subpanel, and breakers.

Grounding

Proper grounding is crucial for safety. The grounding conductor must be sized according to the NEC and properly connected to the grounding electrode system.


Local Codes

Make sure to comply with all local electrical codes.

In summary, your proposed setup is unsafe and likely illegal. Please hire a qualified electrician to do the work properly and safely.
Don't risk your safety, the safety of others, or damage to your property by attempting this project yourself with an improper design. It might seem expensive to hire an electrician, but it's a lot cheaper than a fire or an electrocution. Flag for review

Previous Question Next Question