Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 430.32(A)( 1) - 40 degree C temp rise or less?

User: jes25, Location: Midwest

Asked on: Monday, October 21, 2024 at 3:43 pm EDT
Answered on: Thursday, March 6, 2025 at 4:14 am EST

Question: Hello, I'm teaching some exam prep which includes sizing motor overloads. In 432.(A) 1 it tells us to use a 125% for a motor marked with a temp rise of 40 deg C or less. I know the motors usually have the ambient temp on the nameplate, but I don't see the temp rise on there. How can we tell the temp rise of the motor for application of this article?

That's a great question! You're right, the motor nameplate doesn't always explicitly state the temperature rise. Here's how you can determine the temperature rise for overload sizing, keeping in mind this applies to motors with marked service factors or continuous duty

1. Look for Insulation Class and Service Factor (SF):
Insulation Class is Key

The insulation class of the motor is closely related to its temperature rise. Common insulation classes are A, B, F, and H. Each class has a maximum allowable total temperature (ambient + rise).


Service Factor (SF)

Motors with a service factor of 1.15 or higher, or a temperature rise marked no higher than 40°C, are generally sized at 125% of the motor's full-load amps (FLA). This means the overload is designed to protect the motor at a load exceeding its nameplate FLA.

Motors
without a service factor

If a motor does
not have a service factor of 1.15 or greater, and no specific temperature rise marking (<= 40 degrees), then 115% of FLA is typically used as the maximum overload protection.

2. Typical Assumptions and Practices



Older Motors (pre-NEMA standards)

Older motors might have a temperature rise of 40°C or less and a service factor of 1.15 or higher.

Newer Motors



Most modern general-purpose motors, designed to NEMA standards, will have a temperature rise greater than 40°C
and a service factor of 1.15 or higher. Therefore, they often fall under the 125% rule in 430.32(A)(1).3. When in Doubt, Use the Lower Value and Consult a Qualified Professional



Play it Safe

If you are unsure, it's always safer to start with the lower value (115% of FLA). You can always increase the overload size slightly if nuisance tripping occurs, but never exceed the maximum allowed by the code.

Consult an Engineer

For critical applications or when you have doubts, consult a qualified electrical engineer or motor specialist. They can review the motor specifications and provide accurate overload sizing recommendations.

Example

Let's say you have a motor nameplate that shows:
FLA: 10 amps Service Factor: 1.15 Insulation Class: B Ambient Temp: 40°CIn this case, you would typically use 125% of the FLA for overload sizing: Overload trip current = 10 amps 1.25 = 12.5 amps

Important Considerations for your students



Understanding the Code

Emphasize that the NEC is a minimum standard. Good engineering practice might dictate more conservative overload sizing in certain situations.

Real-World Practice

Encourage students to practice sizing overloads with a variety of motor nameplate examples.


Motor Application

Stress that the correct overload sizing depends on the application of the motor. A motor driving a pump might have different overload requirements than a motor driving a fan.

Overload Relays and Manufacturers' Data

Explain the different types of overload relays (thermal, magnetic, electronic) and how to use manufacturers' data to select the correct trip curves and settings.


Field Adjustments:
Overloads are often field adjustable within a certain range, allowing for fine-tuning to prevent nuisance tripping while still providing adequate protection.By teaching these concepts, you'll equip your students with a solid understanding of how to size motor overloads effectively and safely! Remember, safety and accurate application of the code are paramount. Good luck with your exam prep! Flag for review

Previous Question Next Question