Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: CAT5 use is a wiring method

User: reyamkram, Location: Hanover park, il

Asked on: Wednesday, October 23, 2024 at 4:48 am EDT
Answered on: Thursday, March 6, 2025 at 4:18 am EST

Question: In a factory I was working in I found a machine wired with CAT5 cable they use it as a wiring method to go from switch to switch and to the control panel one machine is 110 volts the other machine is is 24 volts I do not believe that is right where in the NEC can I find that this is a violation if I'm not mistaken Cat 5 cable can only handle around 50 volts thanking you in advance for any and all information it's very highly appreciate it

You are correct to be concerned. Using CAT5 cable for 110V or 24V power distribution is a serious violation of the National Electrical Code (NEC) and creates a significant safety hazard. Here's why and where you'll find the supporting code references

Why it's a violation:
Voltage and Current Rating

CAT5/CAT5e/CAT6 cables are designed for low-voltage, low-current communication signals. They are
not insulated or rated for the voltage and current levels present in 110V or 24V power circuits used for industrial equipment. The insulation is too thin, the conductors are too small, and there is no safety barrier designed to protect workers from electrical shock hazard.

Insulation Breakdown

Applying higher voltage to a CAT5 cable can cause the insulation to break down over time, leading to short circuits, arcing, and potential fires.

Physical Damage

CAT5 cables are typically designed for indoor use and are not robust enough to withstand the physical stresses and environmental conditions found in a factory setting (oil, chemicals, abrasion, etc.). This increases the risk of damage and insulation failure.


Safety Hazard

Using CAT5 cable for power poses a serious electric shock hazard to anyone who comes into contact with the cable, especially if the insulation is compromised.

UL Listing

CAT5 cable is generally UL listed as a communication cable (data transmission), not as a power cable. UL listing is based on specific application parameters and safety testing for intended usage. Using it for power is outside the scope of its listing.

Relevant NEC Articles and Sections



Article 110.3(B) Examination, Identification, Installation, and Use of Equipment

This is one of the most important sections. It states that all equipment, including wiring, must be installed and used in accordance with its listing and labeling instructions. Using CAT5 cable for power clearly violates this. If a cable is listed for communications, you cannot use it for power.

Article 300.3(A) Single Conductors

In general, single conductors for AC wiring are not allowed unless they are part of a cable assembly approved for that purpose, or are specifically permitted in the NEC, such as with grounding conductors. CAT5 cables do not meet this criterion.


Article 300.11(A) Securing and Supporting

Requires cables to be supported in a manner that does not damage them. Using CAT5 cable to run between machines may cause physical damage due to environment, work in progress, or machine vibration.

Article 310 Conductors for General Wiring

This article covers the general requirements for conductors used in electrical wiring. It specifies the types of conductors allowed, their ampacity (current-carrying capacity), and insulation requirements based on voltage levels and environmental conditions. CAT5 cable will not meet these requirements for 110V or 24V power.


Article 392 Cable Trays

If cable trays are used, Chapter 3 details the correct cable types and methods for wiring within.

Article 725 Class 1, Class 2, and Class 3 Remote Control, Signaling, and Power-Limited Circuits

While 24V
can sometimes fall under Class 2 circuits (power-limited), the key is that CAT5 would need to be specifically listed and approved for that use, with the appropriate voltage and current limitations clearly marked. It is highly unlikely that the CAT5 cable being used is listed for this purpose. This article does not authorize CAT5 use for normal power distribution circuits.

Other Relevant Articles

Depending on the specific installation, other articles might apply, such as those related to wiring methods (Chapter 3), grounding (Article 250), and overcurrent protection (Article 240).

Why the NEC doesn't specifically say "Thou shalt not use CAT5 for power"

The NEC is a performance-based code, not a design manual. It sets minimum safety standards but does not attempt to cover every possible misuse of equipment. The general principle is that you must use equipment according to its listing and labeling, and in a safe and workmanlike manner. Using CAT5 for power violates this basic principle.

What to do


Document the violation

Take photos and videos of the wiring setup. Document the voltage levels and equipment involved.2.

Immediately inform your supervisor

Explain the safety hazards and NEC violations to your supervisor or the person responsible for electrical safety at the factory.3.

If your supervisor doesn't take action, escalate the concern

Go to higher management or contact the company's safety officer. If necessary, you can anonymously report the violation to your local electrical inspector or OSHA (Occupational Safety and Health Administration).4.

Do not attempt to fix the problem yourself unless you are a qualified electrician

This is a serious electrical hazard and should only be addressed by a licensed electrician.

Proper Wiring Methods

For 110V and 24V power distribution in a factory setting, use appropriate wiring methods such as:

THHN/THWN conductors in conduit (EMT, Rigid, etc.)

This is a common and robust method for industrial applications.


MC cable (Metal-Clad Cable)

This type of cable is suitable for exposed or concealed wiring and provides physical protection for the conductors.*

SOOW cord

Flexible cord approved for wet locations

In conclusion:
Using CAT5 cable for power distribution is a clear violation of the NEC, a serious safety hazard, and should be corrected immediately by a qualified electrician. Document everything, report the violation, and ensure that the wiring is replaced with an approved wiring method. Flag for review

Previous Question Next Question