User: CrapperEpiphanies, Location: MD, USA
Asked on: Thursday, October 24, 2024 at 9:50 am EDT
Answered on: Thursday, March 6, 2025 at 4:20 am EST
Question: Having a hard time interpreting 350.30: A) indicates that secure fastening is required within 12" "...of each box, cabinet, conduit body, or other conduit termination and shall be supported and secured at intervals not to exceed 4.5'." Exception four says that "For the purposes of 350.30, listed LFMC fittings shall be permitted as a means of securement and support."I take this as for a wall or a pokethrough/floorbox furnitrure feed - the fitting is considered to be the means of securement, as well as the fitting where it terminates into the furniture - so no additional securement required, and the floor acts a means of support (every 4.5'). Does that mean that there's technically no length limit on LFMC furniture feed?I normally like to keep the furniture feeds short, but just making sure that we're allowed to go as long as 6-8 feet if there is a need.Please chime in.
You've hit on a tricky interpretation point that often comes up with LFMC (Liquidtight Flexible Metal Conduit). Let's break it down and clarify
Understanding 350.30 and the Exception
350.30's Primary Requirement
This section generally requires you to secure the LFMC within 12 inches of any termination (box, cabinet, conduit body, etc.) and support it every 4.5 feet. The intent is to prevent strain on connections and maintain the integrity of the wiring system.
Exception 4's Role
This exception is specific to securement and support. It states that if you use listed LFMC fittings, those fittings are themselves considered acceptable securement and support for the purposes of 350.30.
Your Interpretation and Length Limits
Your interpretation is partially correct, but it's crucial to understand the limits of Exception 4: Correct
Using listed LFMC fittings does eliminate the need for additional straps, clamps, or other securement devices within 12 inches of terminations (like where it enters the furniture or the floor box). The fitting itself is the securement.
Where it gets tricky: The 4.5-foot support rule. The exception allows the fitting to be considered the "securement and support" at the termination point. However, you cannot completely disregard the overarching requirement of support at intervals not exceeding 4.5 feet. The floor could be considered support if it is truly providing support to the conduit. The Floor as Support
Whether the floor acts as "support" for the entire length of a 6-8 foot LFMC run is debatable. Generally, unless the LFMC is resting directly on the floor for its entire length (which is unlikely and might create a trip hazard), the floor is not continuously supporting it in the way the NEC intends.
Is There a Length Limit?Technically, the NEC doesn't explicitly state a maximum length for LFMC furniture feed. However, practical considerations and interpretations of the support requirements create an effective length limit.
Here's the reasoning:1. Sagging and Strain
A long, unsupported run of LFMC will sag. This sagging puts strain on the fittings, the conductors within, and potentially on the equipment it's connected to. This is exactly what 350.30 aims to prevent.
2.
"Support" Interpretation
The floor can only be realistically interpreted as a "support" if the conduit is laying on or being supported by it at points not exceeding 4.5' intervals. A 6-8 foot run suspended in air is not being supported by the floor, even if one end is physically close to the floor.3.
Inspector Discretion
The electrical inspector has the final say. They may reject a long LFMC run if they believe it's not adequately supported and could cause issues.
Recommendations and Best Practices Keep it Short
You're already on the right track! Shorter runs are always preferable for furniture feeds. They reduce strain, are neater, and are less likely to be challenged by inspectors. 3-4 feet is often ideal.
Provide Intermediate Support if Necessary
If you must use a longer run (6-8 feet), consider very discreet means of intermediate support. This could be a small clip or tie that attaches the LFMC to the furniture frame or another suitable structural element. Make sure the clip/tie does not damage the LFMC and that it is installed in a way that is mechanically sound.
Consider Other Wiring Methods
In some situations, other wiring methods might be a better choice for longer furniture feeds. For example, "hard-wiring" to a junction box closer to the furniture, using MC cable, or even a power cord specifically designed for furniture may be preferable to a long, unsupported LFMC run.
Consult Your Inspector
If you're unsure, always discuss your installation plan with your local electrical inspector before you begin the work. They can provide guidance specific to your local codes and typical enforcement practices.
In Summary
While Exception 4 of 350.30 allows you to use listed fittings as securement and support at the termination, it doesn't eliminate the implied* need for support on longer runs. Common sense, good workmanship, and the inspector's judgment will dictate what's acceptable. Strive for shorter runs and provide intermediate support if you have to go longer, always keeping safety and code compliance in mind. Flag for review