Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: CTs C400 versu C200

User: [email protected], Location: Weeki Wachee, FL., USA

Asked on: Friday, October 25, 2024 at 1:35 pm EDT
Answered on: Thursday, March 6, 2025 at 4:25 am EST

Question: Any reason I cannot use C200 CTs for this switchgear if the transformer CTs are C400?

Yes, there are several reasons why you likely cannot (or at least should not) use C200 CTs for switchgear protection if the transformer CTs are C400. The choice of CTs depends heavily on the specific application and protective relaying scheme, but here's a breakdown of the common issues

Understanding C200 vs. C400 (and related CT Classes):
"C" Class CTs (ANSI/IEEE Standard)

The "C" designation means the CT is guaranteed to have a ratio error of less than 10% at a specified voltage. The number following "C" indicates that voltage. So:


C200

Guaranteed accuracy (within 10% ratio error) up to 200 volts secondary voltage.

C400

Guaranteed accuracy up to 400 volts secondary voltage.


Why Voltage Matters (Burden)

The secondary voltage a CT needs to produce depends on the burden connected to it. Burden is the impedance connected to the CT's secondary terminals (relays, meters, wiring resistance, etc.). Higher burden requires higher secondary voltage to push the necessary current through it.

Why Mismatching C-Classes Can Cause Problems

1.

Saturation and Inaccurate Measurement



C200 CT with High Burden (Designed for C400)

If you connect a C200 CT to a burden designed for a C400 CT (which is what you'd expect if the transformer CTs are C400), the C200 CT may be driven into saturation at relatively low fault currents.


Saturation Consequences

Once saturated, the CT no longer accurately reflects the primary current. The secondary current becomes distorted and significantly lower than it should be. This can lead to:

Delayed or Failed Protection

Relays may not operate quickly enough or at all because they're receiving incorrect current information.


Miscoordination

If the C200 CT saturates, the relay connected to it might not trip, while relays further upstream (using the C400 CTs) might trip unnecessarily, causing a larger outage than needed.

Equipment Damage

Delayed tripping can allow fault currents to flow for longer, potentially damaging the transformer and other equipment.2.

Differential Protection Schemes (Critical)

If the transformer protection involves differential protection (e.g., 87T relay), using mismatched CTs is extremely dangerous. Differential protection relies on comparing currents at different points in the transformer (primary and secondary sides). If the CTs have significantly different characteristics (especially saturation points), the relay will see a false differential current even under normal operating conditions or during external faults. This can lead to:

Nuisance Tripping

The differential relay could trip the transformer unnecessarily, causing an outage.


Failure to Detect Internal Faults

A true internal fault might be masked by the CT errors, preventing the relay from operating and allowing the fault to escalate.3.

Burden Mismatch in General

The switchgear's relays and wiring were likely designed with a certain secondary burden in mind, anticipating the C400 CTs. Using C200 CTs may mean: The secondary voltage needed to drive the burden with rated secondary current will exceed the voltage class rating of the CT.

In Summary: When is it Okay?
Very Low Burden

The
only scenario where a C200 might possibly work in place of a C400 is if the actual burden connected to the CT is extremely low and the fault current levels are also expected to be low. This is rarely the case in switchgear connected to a transformer. Even then, it's poor practice and should be avoided.

Testing & Calculations

You MUST perform detailed calculations and testing to confirm that the C200 CT will not saturate under the worst-case fault conditions and that the relay settings are still appropriate. This involves:

Calculating the actual burden
(relay impedance, wiring resistance, test switches, etc.). Determining the maximum fault current the CT will experience. Consulting the CT's saturation curve (B-H curve) to verify that it won't saturate at that fault current with the calculated burden. Verifying relay settings based on the new CT ratio and potential saturation characteristics.

Recommendation



Always use the correct CT class (or higher)

If the system is designed for C400 CTs, use C400 CTs. Using C200 CTs as a "cheaper" or "easier" option is a false economy that puts your equipment at risk. It may also violate electrical codes.


Consult with a qualified protection engineer

The selection and application of CTs is a critical part of power system protection. A protection engineer can properly assess the system requirements and ensure that the correct CTs are used.

Review Original Design Documentation

Check the original switchgear design drawings, relay settings, and specifications. This documentation should specify the required CT class, ratio, and burden.


Consider "X" Class CTs (TPX, TPY, TPZ in IEC Standard)

If accuracy is critical for a longer duration, consider using CTs meeting IEC standards TPX, TPY, or TPZ. These are designed to minimize saturation during transient fault conditions.*

Verify Relay Settings

Whenever CTs are changed, re-evaluate and adjust the relay settings to ensure proper protection coordination.

Bottom Line:
It's highly improbable that you can safely use C200 CTs when C400 CTs are specified. You risk misoperation of protection and equipment damage. Get an expert opinion before proceeding. Flag for review

Previous Question Next Question