User: Stubby, Location: Climax
Asked on: Friday, October 25, 2024 at 3:34 pm EDT
Answered on: Thursday, March 6, 2025 at 4:25 am EST
Question: For use above live parts. Use with pvc. No way I can get turned down from the inspector on this. I'm sure they will find away around this.
Okay, I understand you're looking for electrical supplies to use above live parts, specifically with PVC conduit, and you want something that's virtually guaranteed to pass inspection. You're anticipating the inspector might be difficult. Here's the best advice I can give you, breaking down the situation and providing recommendations
Key Considerations and Principles:
Safety First
Working around live electrical parts is extremely dangerous and should only be done by qualified professionals with the proper training, tools, and personal protective equipment (PPE).
If you are not a qualified electrician, DO NOT attempt to work on or near live electrical components. Contact a licensed electrician. NEC Compliance
The National Electrical Code (NEC) is the governing standard for electrical installations in most of the US. Your installation must comply with the NEC. Inspectors are there to ensure that compliance for safety.
Listed and Labeled Equipment
All electrical equipment you use MUST be "listed" by a nationally recognized testing laboratory (NRTL) like UL, ETL, CSA, etc., and labeled for its intended use. This means it has been tested and certified to meet safety standards. Using equipment that is not listed and labeled is a major code violation and a serious safety hazard.
Clearance and Working Space
The NEC specifies minimum clearance requirements around electrical equipment to provide safe working space for maintenance and repairs. This will impact your conduit runs and where you can place things.
Insulation and Protection
Anything placed above live parts must provide adequate insulation and protection to prevent accidental contact and short circuits.
Accessibility
The NEC also addresses accessibility. You can't bury live parts or make them inaccessible without proper means of access (e.g., a junction box with a cover).
Possible Solutions (Assuming Compliant Installation - CONSULT A QUALIFIED ELECTRICIAN)
Based on your description, here are a few possibilities, but remember, the specific solution depends entirely on the details of your installation and the NEC.1.
Non-Conductive Barriers/Covers
Listed Insulating Barriers
These are specifically designed to be placed over live parts to provide a physical barrier and electrical insulation. Look for products that are UL-listed for this purpose. They are often made of fiberglass reinforced polyester or polycarbonate.
Insulated Covers
Similar to barriers, but they might be designed to cover specific components (e.g., busbars, terminals). How to ensure they pass: Ensure the barriers/covers are rated for the voltage and amperage of the live parts they are covering. Make sure they provide adequate clearance to the live parts (check the manufacturer's specifications and local codes). Document the listing information for the inspector. Install per the manufacturer's instructions.2.
Conduit Placement & Material (PVC)
PVC Conduit
PVC conduit is a non-conductive raceway and is acceptable for many applications, including those above live parts, provided it is installed correctly and meets all other code requirements.
Proper Supports
Ensure the PVC conduit is properly supported according to the NEC.
Secure Connections
Use proper PVC fittings and cement to create a watertight and secure raceway system. How to ensure it passes: Ensure the conduit is sized correctly for the number and size of conductors it will contain. Use only listed PVC conduit and fittings. Properly support the conduit at the intervals specified in the NEC. Properly ground the metal enclosures that the conduit is connected to. Do not exceed the maximum number of bends allowed in a conduit run.3.
Insulated Conductors
Proper Wire Type
Use conductors with the correct insulation rating (e.g., THHN/THWN-2) for the environment and voltage.
Secure Terminations
Ensure all wire terminations are made with approved connectors and are properly torqued. How to ensure they pass: Ensure the conductors are sized correctly for the amperage of the circuit. Use only listed conductors. Properly terminate the conductors at all connection points.4.
Working with the Inspector Open Communication
Before you start any work, talk to the inspector. Explain your plan and ask for their feedback. This is the best way to avoid surprises and ensure compliance.
Documentation
Keep all product information (spec sheets, UL listings, etc.) readily available for the inspector.
Be Professional
Treat the inspector with respect, even if you disagree with them. Remember, they are there to ensure safety.
Why Inspectors Might "Find a Way Around" Your Initial Plan
Inspectors don't arbitrarily reject installations. Here are some common reasons for rejection:
Code Violations
The most obvious reason. Your installation simply doesn't meet the requirements of the NEC or local codes.
Unsafe Practices
Even if something technically meets the code, an inspector might reject it if they believe it creates an unsafe condition.
Incorrect Use of Equipment
Using equipment for a purpose it wasn't designed or listed for.
Lack of Documentation
Failing to provide the necessary documentation to prove that the equipment is suitable for the application.
Poor Workmanship
Sloppy or unprofessional work can raise red flags and lead to closer scrutiny.
Important Disclaimer
This information is for general guidance only and should not be considered a substitute for professional electrical advice. Always consult with a licensed electrician and your local electrical inspector to ensure that your installation complies with all applicable codes and regulations.
Working with electricity can be dangerous, and improper installations can lead to fire, injury, or death. Flag for review