Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: sizing breaker and wire for this welding machine

User: Cartoon1, Location: Florida

Asked on: Monday, October 28, 2024 at 2:05 pm EDT
Answered on: Thursday, March 6, 2025 at 4:31 am EST

Question: I have a Ironman 240 Welding machine. I have a 240V system. I'm thinking of putting a 50A amp breaker with #8 copper 75C rating. Information below. Should i up size the breaker for startup current? Also, should i upsize cable to #6 because it is technically 50.8 and not 50?Performance Data:Rated Output: 200 A at 24 VDC, 60% duty cycleOpen Circuit Voltage: 40 VDCAmperes Input at Rated Load (208 V / 240 V): 57.0 / 50.8KVA / KW: 11.4 / 7.1Thank you

Okay, let's break down the electrical requirements for your Ironman 240 welder and determine the correct breaker and wiring.

Understanding the Code and Requirements National Electrical Code (NEC)

This is the governing code for electrical installations in the US (and often adopted or adapted elsewhere). We'll refer to it for proper sizing.


Nameplate Data is Key

The information on your welder's nameplate is critical. You've provided it, which is excellent.

Duty Cycle

The 60% duty cycle means the welder can operate at its rated output (200A at 24VDC) for 6 minutes out of every 10 minutes. This affects the calculations.


Startup Current (Inrush Current)

Welders, like many inductive loads, can draw a significantly higher current briefly when they're first turned on. This is the "startup current."

Conductor Ampacity

This is the maximum current a conductor (wire) can safely carry continuously without overheating.


Overcurrent Protection (Breakers/Fuses)

These devices are designed to protect the wiring and equipment from overloads and short circuits. They are not intended to be run at their maximum rating continuously.

Analysis and Recommendations
1. Breaker Sizing



NEC Article 630 (Electric Welders)

This article specifically addresses the electrical requirements for welders. It allows for a reduced conductor ampacity and overcurrent protection compared to continuously loaded circuits. This is due to the intermittent nature of welding.


NEC 630.11(A)

Typically requires conductors to have an ampacity of not less than 100% of the rated primary current of the welder. Your welder draws 50.8A at 240V.

NEC 630.12(A)

The overcurrent device (breaker) shall not exceed 200% of the rated primary current. In your case, 200% of 50.8A is 101.6A.
2.


Conductor Sizing



#8 AWG Copper (75°C Rating)

According to NEC Table 310.16, #8 AWG copper wire with a 75°C insulation rating has an ampacity of 50A.

Temperature Correction

Ensure that the terminals on your breaker and welder are rated for 75°C. If not, you may need to use the 60°C ampacity rating for #8 copper, which is lower.


Voltage Drop

Voltage drop can be a concern, especially on longer runs. Use a voltage drop calculator to determine if the voltage drop is acceptable for your run length. Generally, keep voltage drop under 3%.3.

Startup Current

NEC Article 630 allows for upsizing the overcurrent protection based on the welder's duty cycle and inrush current. Your welder has a 60% duty cycle. The breaker can be upsized to 150% or 200% of the rated current. A 60 or 70 amp breaker should be sufficient.

Calculations



Conductor Ampacity Requirement

50.8 amps


Breaker Size

50.8A x 1.5 - 2.0 = 76.2 - 101.6 amps.

Recommendations



Breaker

Install a

60 or 70 amp breaker
. This will provide adequate protection against overloads. Wiring

You should upgrade your wiring to #6 copper. #8 may be able to support your welding needs, but #6 is needed for a 60 - 70 amp breaker.

Important Considerations



Local Codes

Always check and comply with your local electrical codes, as they may have stricter requirements than the NEC.


Qualified Electrician

It is highly recommended that a qualified and licensed electrician perform this work. Electrical work can be dangerous, and incorrect wiring can lead to fire hazards, equipment damage, or personal injury. A professional will ensure the installation meets all applicable codes and safety standards.

Distance

If the run length of the wire is significant, you should calculate the voltage drop to ensure it is within acceptable limits. Longer runs may require larger wire sizes to minimize voltage drop.


Grounding

Ensure proper grounding of the welder and the circuit.

Receptacle

Choose a 50-amp rated receptacle that matches the plug on your welder.


Strain Relief

Properly strain-relieve the cable at both the breaker panel and the welder to prevent stress on the connections.

In summary, using a 50A breaker with #8 wire is not the best choice. Upgrade to a 60/70A breaker and #6 copper wire.
Flag for review

Previous Question Next Question