Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: MCA and MOCP wire size/fuse clarification

User: acolella, Location: New Jersey

Asked on: Wednesday, October 30, 2024 at 7:08 pm EDT
Answered on: Thursday, March 6, 2025 at 4:39 am EST

Question: I'm sure this has been beaten to death on this forum and many other forums. It has been beaten to death at my place of employment as well but we're back on it again.I'm at an edge case with wire size/fuse size. I have an HVAC unit that has an MCA of 58 amps and an MOCP of 70 amps that is supplied with #6 wire. #6 is good for 65 amps going by the 75°C column so we're definitely good there. I'm wondering about the fuse size. I know the unit MOCP is 70 amps but is my fuse selection at all limited by the wire size, or do I simply look at MCA for wire size and MOCP for fuse selection and be done with it?I understand that when strictly motor protection is concerned, there are cases where the circuit can be "overfused" relative to the wire size to avoid nuisance tripping at startup. I'm wondering if my situation is one where this is also acceptable. This is in a laboratory environment and not in the field but I'm just curious how this situation would be handled in the field.

You're right, this is a classic NEC interpretation issue! Let's break it down, focusing on your specific situation and the code articles at play.

The Core Principle: Protection & Coordination

The NEC aims to protect both the equipment and the conductors. You're hitting the point where those two protections seem to conflict.

Your Situation - Recap



MCA (Minimum Circuit Ampacity)

58 Amps


MOCP (Maximum Overcurrent Protection)

70 Amps

Conductor

#6 AWG (rated for 65 Amps at 75°C)

The NEC Articles in Play



440.22(A) Protection Against Overcurrent

This section specifically addresses the overcurrent protection for air-conditioning and refrigerating equipment. It essentially allows the MOCP to exceed the ampacity of the conductor, with qualifications.

440.22(B) Single Motor Compressor. This is where the exceptions to the 175%/225% OCPD rule are found. 240.4(B) and (D)

These rules restrict allowing "next size up" OCPD protection for conductors under specific scenarios. These rules generally don't apply here due to

440.22. 110.3(B) Installation and Use

Listed equipment shall be installed and used in accordance with any instructions included in the listing or labeling.

The Answer (Detailed Explanation)


Conductor Sizing

Your #6 wire is rated for 65 amps, which is above the MCA of 58 amps, so you meet the requirement for proper conductor sizing. The conductor is properly sized to carry the
continuous load.2.

Overcurrent Protection (Fuse Size)

Here's where the interpretation is critical.


Following the MOCP

You're permitted to use a 70 amp fuse if the HVAC equipment is specifically listed and labeled with a MOCP of 70 amps, and the equipment's instructions don't prohibit it. This is based on

440.22(A), which acknowledges that HVAC equipment (especially with motors) may require a higher overcurrent protection to avoid nuisance tripping during starting. The equipment is designed to handle short-term inrush currents.

Limitations

The MOCP is a maximum. You are allowed to use a smaller fuse. For example, a 60 amp fuse would comply with the 65 amp wire rating and the MCA rating as well. The MOCP is not a minimum. If you have an undersized conductor and a 70 amp fuse, you could have a low-level fault current that exceeds the ampacity of the conductor before the 70 amp fuse trips. The conductor could be damaged.3.

Coordination

While the NEC allows the 70-amp fuse, it doesn't remove the need for good engineering judgment. Consider these factors:

Actual Load Profile

How often does the HVAC unit operate near its MCA? If it mostly runs at a lower load, a smaller fuse might be suitable.


Fuse Type

Time-delay fuses (like dual-element fuses) are often used in motor circuits because they can withstand inrush currents without tripping unnecessarily. Using a time-delay fuse is critical in your situation if you're going to use the full 70-amp MOCP. A standard fuse will likely trip on startup.

Manufacturer's Instructions

Always follow the HVAC unit manufacturer's instructions. If they specify a particular fuse type or size range, adhere to that.

How This is Handled in the Field

In the field, electricians generally follow the MOCP on the equipment nameplate. However, a good electrician will:
Verify the conductor size is adequate for the MCA. Use the correct type of fuse (time-delay). Consult the manufacturer's instructions if there are any doubts or conflicting information. Check for any local amendments to the NEC that might affect the interpretation.

In Your Laboratory Environment

Since you're in a controlled laboratory environment, you have more flexibility to analyze the situation and make an informed decision. Consider:


Monitoring

Can you monitor the actual current draw of the HVAC unit during startup and operation? This data can help you determine the optimal fuse size.

Collaboration

Discuss the situation with the facilities engineers or other qualified personnel. They may have insights into the equipment's performance and historical issues.


Documentation

Document your decision-making process, including the code articles you considered, the data you collected, and the rationale for your final fuse selection. This is especially important in a laboratory setting where safety and compliance are paramount.

In Summary:You can use the 70 amp fuse if the HVAC unit is labeled with that MOCP and the manufacturer's instructions don't prohibit it, but it's not a requirement. The #6 conductor is properly sized, but that alone does not mean you must use the 70 amp fuse, especially if you're concerned about potential conductor damage from a low-level fault. Using a smaller, time-delay fuse that is closer to the conductor's ampacity is a reasonable and potentially safer approach. A 60-amp time delay fuse would seem like a reasonable compromise.Always prioritize safety and follow the manufacturer's instructions. Flag for review

Previous Question Next Question